Seagate ST200FM0012 manual SAS transmitters and receivers, Power, Ready LED Out, LED drive signal

Page 63

11.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 20. The receiver is AC coupling to eliminate ground shift noise.

Figure 20. SAS transmitters and receivers

11.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

11.5SIGNAL CHARACTERISTICS

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 24 for signal type and signal name information.

11.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 25.

Table 25 Ready LED Out conditions

NORMAL COMMAND ACTIVITY

 

LED STATUS

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Drive stopped, not ready, and no activity

Off

 

Off

 

 

 

 

Drive stopped, not ready, and activity

On

 

On

(command executing)

 

 

 

 

 

 

 

Drive started, ready, and no activity

On

 

Off

 

 

 

 

Drive started, ready, and activity

Off

 

On

(command executing)

 

 

 

 

 

 

 

Drive transitioning from not-ready state to

 

Blinks steadily

ready state or the reverse.

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

FORMAT UNIT in progress,

 

Toggles on/off

 

 

 

 

The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resistor are external to the drive. See Table 26 for the output characteristics of the LED drive signals.

Table 26 LED drive signal

STATE

TEST CONDITION

OUTPUT VOLTAGE

 

 

 

 

 

LED off, high

0 V ≤ VOH ≤ 3.6 V

-100 μA < IOH < 100 μA

 

LED on, low

IOL = 15 mA

0 ≤ VOL ≤ 0.225 V

 

PULSAR.2 SAS PRODUCT MANUAL, REV. C

57

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Pulsar.2 SAS Revision Date Description of changes Document Revision HistoryContents About Fips About SELF-ENCRYPTING Drives PHYSICAL/ELECTRICAL SpecificationsDefect and Error Management InstallationInterface Requirements Figures Seagate Technology Support Services Standard models Standard SED models Fips 140-2 Level ScopeApplicable Standards and Reference Documentation Electromagnetic compatibilityElectromagnetic susceptibility Korean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickChina Restriction of Hazardous Substances RoHS Directive General Description 524 800GB 400GB 200GB 100GB512 520Thin Provisioning Product Configuration Logical Block ProvisioningThin Provisioning capabilities Protection Information PI and Security SED Format Unit commandPI and SED Drive Configuration UnmapTypical Access Time μsec Performance CharacteristicsFormat Mode Dcrt Bit IP Bit 800GB 400GB 200GB 100GB Access timePerformance Performance Managed Life WarrantyPerformance Usage Based Warranty ST800FM00 ST400FM00 ST200FM00 ST100FM00Caching write data Reliability Specifications Unrecoverable ErrorsInterface errors Write Amplification SSD Percentage Used Endurance IndicatorWear Leveling Garbage CollectionControlling S.M.A.R.T Preventive maintenanceHot plugging the drive 4 S.M.A.R.TPredictive failures Performance impactReporting control Determining rateParameter Code Description 800/400/200/100GB Temperature Log Page 0DhExtended test Function Code 010b Product warrantyManaged Life Warranty Usage Based WarrantyPeak operating mode PHYSICAL/ELECTRICAL SpecificationsPower consumption Startup power800GB 6.0GB 800GB standard model DC power requirements400GB 6.0GB 400GB standard model DC power requirements200GB 6.0GB 200GB standard model DC power requirementsGeneral DC power requirement notes 100GB standard model DC power requirementsPower sequencing Conducted noise immunityCurrent profiles Current profiles for 400GB models Current profiles for 100GB models 800GB models in 6Gb operation 400GB models in 6Gb operation200GB models in 6Gb operation Environmental Limits 100GB models in 6Gb operationTemperature a. Operating Relative humidityEffective altitude sea level a. Operating Shock Shock and vibrationAir cleanliness VibrationCorrosive environment Weight Pounds 160 grams Weight Pounds 100 grams Security Level PurposeValidation Program Seagate Enterprise SEDLocking SP Admin SPDefault password About SELF-ENCRYPTING DrivesData Bands SSD Physical format address descriptor Defect and Error ManagementDrive Error Recovery Procedures Setting and determining the current Type Level Levels of PIIdentifying a Protection Information drive Physical interface InstallationX = F 15lb = 67N Task management responses Interface RequirementsTask management functions SAS task management functions supportedFormat Unit Supported commandsPersistent Reserve Reassign Blocks Write and Verify Pulsar.2 Inquiry data Inquiry dataMode Sense data Mode Sense data for 800GB drives Mode PagesMode Sense data for 400GB drives Mode Sense data for 200GB drives Mode Sense values for 100GB drives Miscellaneous features Miscellaneous statusSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out PowerLED drive signal SAS transmitters and receiversDifferential signals General interface characteristics5G B/ S 0G B/ S Index Index SAS See also cooling Americas Seagate Technology LLC

ST800FM0002, ST100FM0002, ST200FM0002, ST400FM0012, ST800FM0032 specifications

The Seagate ST100FM0012, ST800FM0012, ST400FM0042, ST400FM0002, and ST100FM0052 are high-performance hard drives designed for enterprise applications, offering advanced features and reliability for demanding workloads.

The ST100FM0012 is a 10TB hard drive that strikes a balance between capacity and performance. It utilizes a 7200 RPM spindle speed and features a 256MB cache, enabling efficient data access and enhanced read/write performance. With Seagate’s AgileArray technology, the ST100FM0012 is optimized for NAS environments, providing multi-drive reliability and error recovery.

The ST800FM0012 is an 8TB variant that shares many features with its 10TB counterpart but is tailored for organizations needing robust storage without reaching the highest tier of capacity. Its dual-plane rotational vibration technology minimizes vibration in multi-drive systems, ensuring sustained performance over prolonged use. This makes it an excellent choice for virtualization and data-intensive applications.

The ST400FM0042 offers a 4TB capacity suited for smaller enterprise needs or as a backup solution. With an impressive performance profile, including a 7200 RPM speed and 128MB cache, it accommodates both sequential and random workloads with ease. This drive stands out with its PowerChoice technology, allowing users to manage power consumption and reduce operational costs.

Another 4TB option, the ST400FM0002, is particularly designed for hybrid configurations, pairing the fast access of the hard drive with the speed of SSDs. It features Seagate's advanced thermal management technologies, ensuring optimal operating temperatures and performance stability during intensive workloads.

The ST100FM0052 rounds out the lineup with a 10TB capacity but is specifically aimed at surveillance applications. It supports a workload rate of 180TB per year, making it ideal for always-on recording scenarios. The drive is built with optimized firmware, which ensures enhanced performance in write-intensive environments, essential for video recording and security systems.

All these drives are equipped with Seagate’s proprietary technologies, including data recovery services and built-in data protection features, ensuring data integrity and security. The drives are built for durability, reliability, and high performance in mission-critical environments, making them indispensable components of modern enterprise data storage solutions. With capacities ranging from 4TB to 10TB, they cater to varying storage needs across different sectors.
Top Page Image Contents