Seagate ST9146802SS, ST973402SS manual Installation, Drive orientation

Page 51

8.0Installation

Savvio disc drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accomodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend the use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 9.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 9. Physical interface

8.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

Savvio 10K.2 SAS Product Manual, Rev. B

41

Image 51
Contents Savvio 10K.2 SAS Page Savvio 10K.2 SAS Page Revision Date Revision status summary sheetPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesSavvio 10K.2 SAS disc drive List of FiguresPage Savvio 10K.2 SAS disc drive ScopeSavvio 10K.2 SAS Product Manual, Rev. B Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean MIC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsSavvio 10K.2 SAS Product Manual, Rev. B General description Standard features Media descriptionPerformance Programmable drive capacity Factory-installed accessoriesReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsGeneral performance characteristics Format command execution time for 512-byte sectors minutesStart/stop time Prefetch/multi-segmented cache controlCache operation Prefetch operation Caching write dataPage Savvio 10K.2 SAS Product Manual, Rev. B Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsMilliseconds 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Reporting controlDetermining rate Predictive failuresImplementation Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST DST failure definitionShort test Function Code 001b State of the drive prior to testingInvoking DST Short and extended testsShipping Product warrantyLog page entries AbortProduct repair and return information ST9146802SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsST973402SS DC power requirements General DC power requirement notesST973402SS Gbit mode Amps +5V +12V Power sequencingConducted noise immunity Current profilesST973402SS current profile Power dissipation ST9146802SS in 3 Gbit operationST973402SS in 3 Gbit operation Environmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightAir cleanliness VibrationCorrosive environment Acoustics Mounting configuration dimensions Mechanical specificationsSavvio 10K.2 SAS Product Manual, Rev. B Defect and error management Drive internal defects/errorsDrive error recovery procedures Page Background Media Scan SAS system errorsMedia Pre-Scan Deferred Auto-ReallocationIdle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingSavvio 10K.2 SAS Product Manual, Rev. B Interface requirements SAS featuresDual port support Scsi commands supported Commands supported by Savvio SAS family driveCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Bytes Data hex Mode Sense dataInquiry data Savvio inquiry dataPage Mode Data Header 08 8b b9 98 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsJitter tolerance masks Receive eye maskFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatTransmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Tctf ISI loss example at 1.5 Gbps Receiver characteristicsPresales Support Seagate Technology support servicesWarranty Service Internet MySeagate Spp.seagate.comData Recovery Services Data Recovery Services Authorized Service CentersFAX services-All Europe toll call Call center Presales and Technical Support Warranty ServiceToll-free support numbers Seagate Service Centers Numerics IndexPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 84 pages 36.64 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.