Seagate ST973402SS Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 70

NC - No connection in the drive.

9.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 14. The receiver is AC cou- pling to eliminate ground shift noise.

 

TX

Transmitter

Differential

Transfer Medium

100

 

 

TY

Figure 14. SAS transmitters and receivers

.01

.01

RX

Receiver

100

RY

9.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

9.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 23 for signal type and signal name information.

9.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 24.

Table 24: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

60

Savvio 10K.2 SAS Product Manual, Rev. B

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Savvio 10K.2 SAS Page Savvio 10K.2 SAS Page Revision status summary sheet Revision DatePage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Savvio 10K.2 SAS disc drivePage Scope Savvio 10K.2 SAS disc driveSavvio 10K.2 SAS Product Manual, Rev. B Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean MICReference documents European Union Restriction of Hazardous Substances RoHSSavvio 10K.2 SAS Product Manual, Rev. B General description Media description Standard featuresPerformance Formatted capacities Factory-installed accessoriesReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeFormat command execution time for 512-byte sectors minutes General performance characteristicsPrefetch/multi-segmented cache control Start/stop timeCache operation Caching write data Prefetch operationPage Savvio 10K.2 SAS Product Manual, Rev. B Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T MillisecondsPredictive failures Reporting controlDetermining rate Thermal monitorDST failure definition Temperature Log Page 0Dh Parameter Code DescriptionDrive Self Test DST ImplementationShort and extended tests State of the drive prior to testingInvoking DST Short test Function Code 001bAbort Product warrantyLog page entries ShippingProduct repair and return information DC power requirements Physical/electrical specificationsAC power requirements ST9146802SS DC power requirementsGeneral DC power requirement notes ST973402SS DC power requirementsST973402SS Gbit mode Amps Current profiles Power sequencingConducted noise immunity +5V +12VST973402SS current profile ST9146802SS in 3 Gbit operation Power dissipationST973402SS in 3 Gbit operation Temperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingVibration Air cleanlinessCorrosive environment Acoustics Mechanical specifications Mounting configuration dimensionsSavvio 10K.2 SAS Product Manual, Rev. B Drive internal defects/errors Defect and error managementDrive error recovery procedures Page SAS system errors Background Media ScanDeferred Auto-Reallocation Media Pre-ScanIdle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSavvio 10K.2 SAS Product Manual, Rev. B SAS features Interface requirementsDual port support Commands supported by Savvio SAS family drive Scsi commands supportedCommand name Command code Supported Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Commands supported by Savvio SAS family drive Savvio inquiry data Mode Sense dataInquiry data Bytes Data hexPage Mode Data Header 08 8b b9 98 00 00 02 Supported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewReceive eye mask Jitter tolerance masksJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Tctf Receiver characteristics ISI loss example at 1.5 GbpsInternet MySeagate Spp.seagate.com Seagate Technology support servicesWarranty Service Presales SupportData Recovery Services Authorized Service Centers Data Recovery ServicesCall center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Seagate Service Centers Index NumericsPage SAS See also cooling Page Seagate Technology LLC
Related manuals
Manual 84 pages 36.64 Kb

ST973402SS, ST9146802SS specifications

The Seagate ST973402SS and ST9146802SS are high-performance, enterprise-grade hard drives designed to meet the demanding needs of data-intensive applications. These drives are part of Seagate's Savvio and Barracuda product lines, aimed specifically at businesses and institutions requiring reliability, speed, and efficiency in storage solutions.

The ST973402SS is a 73GB, 2.5-inch hard drive, while the ST9146802SS offers a larger capacity of 146GB. Both models utilize a 10,000 RPM spindle speed, which significantly enhances their ability to handle fast data read and write operations. This speed ensures reduced latency and improved overall performance, making them ideal for environments where rapid access to data is crucial.

One of the standout features of these drives is their support for Serial Attached SCSI (SAS) interface. SAS technology provides a point-to-point connection, which allows for increased data transfer rates compared to traditional SATA drives. The ST973402SS and ST9146802SS are capable of transferring data at speeds of up to 600 MB/s, facilitating efficient data transfers in enterprise systems.

In terms of reliability, both models offer advanced features designed to improve data integrity and durability. They are built to withstand high workloads, with an annualized workload rate of up to 550 TB per year. This makes them well-suited for applications like databases and transactional storage, where sustained performance is required. Additionally, the drives feature Seagate’s PowerFit technology, which optimizes performance while minimizing power consumption.

To enhance data security, the drives come equipped with self-encrypting technology, ensuring that sensitive data is protected through hardware-based encryption. This is particularly important in environments where data breaches can lead to significant operational impacts.

The drives are also designed to operate efficiently in terms of thermal management, featuring robust heat dissipation capabilities. This helps to maintain optimal performance levels while prolonging the lifespan of the drives.

Overall, the Seagate ST973402SS and ST9146802SS are robust and reliable hard drives that cater to the needs of enterprise environments, combining high capacity, exceptional speed, advanced security features, and energy efficiency to help businesses maintain and manage large volumes of data effectively. With their proven performance and innovative technologies, these drives are well-equipped to support a wide range of applications in modern data centers.
Top Page Image Contents