Conformity and Standard, UPS Environmental | Liebert 130 kVA

User Manual

Hipulse - Single Phase ‘1+N’ UPS System

130 kVA - 110V

Chapter 9

Specification

This specification describe requirements for an Uninterruptible Power System (UPS).

9.1Conformity and Standard

The UPS has been designed to conform the following standards: IEC, EN

9.2UPS Environmental

The UPS shall be able to operate under the following environmental conditions without damage or degradation in electrical operating characteristics:

Environmental Characteristics	Units
Rated Power	kVA	130
Operating Temperature	ºC	0 to 45 ºC
Relative Humidity	%	= 90% at 31 ºC, Saliferrous, Humid
Altitude of operation	m	= 1000m above sea level
Storage/ transport temperature	ºC	-25 to 70 ºC

9.3UPS Mechanical Characteristics

Mechanical	Units	130 kVA
Characteristics		6 pulse
Height	mm	1900
Width	mm	1400
Depth	mm	925
Ventilation	-	By internal intake fans
Cable entry	-	Bottom
Protection	IP	41

71

Image 91

Liebert 130 kVA user manual Conformity and Standard, UPS Environmental, UPS Mechanical Characteristics

Contents

Hipulse Single Phase ‘1+N’ UPS System Hipulse Single Phase ‘1+N’ UPS System Dear Customer Hipulse Single Phase ‘1+N’ UPS System Rev. No Revision details Hipulse Single Phase ‘1+N’ UPS System Registered Head Office Hipulse Single Phase ‘1+N’ UPS System East Zone Hipulse Single Phase ‘1+N’ UPS System Safety Procedure Hipulse Single Phase ‘1+N’ UPS System General Hipulse Single Phase ‘1+N’ UPS System General Introduction Hipulse Single Phase ‘1+N’ UPS System Operating Instructions Hipulse Single Phase ‘1+N’ UPS System Annexure Hipulse Single Phase ‘1+N’ UPS System Hipulse Module Design Single Module block diagramIntroduction Design Concept Bypass Supplies UPS Power switches configuration Normal Operation Return of power mainsOff-Battery UPS Module fault Overload Maintenance Bypass System Expansion UPS Power Switch ConfigurationBattery circuit breaker Battery temperature compensation Hipulse Single Phase ‘1+N’ UPS System Installation Procedure Environmental considerations Battery locationUPS location Mechanical Considerations Preliminary Checks Installation Drawings Overall General Arrangement for 130kVA Single Phase UPS Cable Entry Details Module input cables Power CablingSystem Configuration Battery cables Cable Connections Safety earthCable rating General Notes Protective devices Protection against earth faults RCD devicesSplit Bypass Input Connections UPS BatteryCabling procedure Parallel 1+N Auxiliary Connections Input-module Parallel Connections Cable connections for 130 kVA 1Ph UPS +VE -VE Control cables Battery ControlAuxiliary Terminal Block detail Description Auxiliary Terminal Block X3 and X4 at UPS Emergency Stop Battery ConnectionBack Feed Protection Hipulse Single Phase ‘1+N’ UPS System UPS Operator Control / Display Panel Operator Control and Display Panel Mimic indications Inverter control switchSingle module operator control panel Operator control panel Operator Panel and LCD Display Menu Control switches Bargraph Selection Output Parameters Menu Options EPO on UPS module Or. for Instanc e Map of screen display available to operator Main Menu Window Default WindowLCD Display Panel Messages Initializing Window Info Window Alarm / Warning Messages Option Selection Mode Shutdown General notes Power SwitchesOn Static Bypass Location of Power Isolators Ecomode the message Load on Bypass will not appear Battery C.B. Open Bypass Switch Open Ecomode Normal Operation Your load is now powered via the Static Bypass system Your load is now powered via the Static Bypass system Procedure for completely powering down the UPS UPS is now completely powered down Adding a single module to an existing system If YOU are not Sure What YOU are Doing Then do not do IT Ecomode INV OFF VIA Display Load on Bypass Setting the Battery Test Changing the current Date and Time Language Selection Hipulse Single Phase ‘1+N’ UPS System Safety Battery Installation UPS Batteries Battery population Temperature considerations Introduction Battery protectionBattery Racks Connecting the Battery Battery Supply To UPS Cabinet Battery circuit breaker Battery Installation Battery Control and Power Connections Battery temperature Board LED Interpretation Display Panel Interpretation Procedure to carry out the reset see Operating Instructions Display Panel Messages Sr. No Display Message Alarm Interpretation Bypass Switch Open BYP. Absent Battery Under Test BYP Xfer Count Block Hipulse Single Phase ‘1+N’ UPS System General + N System Battery 1+N System block diagram with Separate Batteries Connection of 1+N system parallel single bus cables Installation procedureInter-module control Connection of EPO Push Button Operating Instruction System Start-up and shutdown procedures Separate Batteries Default window Hipulse Single Phase ‘1+N’ UPS System Complete system shutdown Display Panel message interpretation in 1+N System Conformity and Standard UPS Mechanical CharacteristicsUPS Environmental C T I F I E R I N P U T M a I N S UPS Electrical Characteristics Rated Power KVA 130 UPS Electrical Characteristics DC Intermediate Circuit V E R T E R O U T P U T UPS Electrical Characteristics Inverter Output Protection, bypass line UPS Electrical Characteristics Bypass Input Mains Hipulse Single Phase ‘1+N’ UPS System Hipulse Single Phase ‘1+N’ UPS System Hipulse Single Phase ‘1+N’ UPS System RAM Connections Remote Alarm Monitor 220/240V AC 50 Hz UPS Indication & Metering TerminationProtection Bypass Isolation Cubicle