Seagate DB35.4 Configuring and mounting the drive, Handling and static-discharge precautions

Page 23

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static-discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive by its edges or frame only.

•The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

DB35.4 Series SATA Product Manual, Rev. C

17

Page 22 Page 24
Image 23
Page 22 Page 24
Contents ST3250310CS DB35.4 Series SataRevision Date Revision historyContents DB35.4 Series Sata Product Manual, Rev. C List of Figures Page Introduction About the Serial ATA interface Specification summary tables Drive specificationsDrive specification ST3250310CS Drive specifications summary for 250 Gbyte modelDB35.4 Series Sata Product Manual, Rev. C Recording and interface technology Default logical geometryLBA mode Formatted capacityTypical seek times msec Read Write Physical characteristicsSeek time Start/stop timesPower specifications Voltage tolerance Typical current profilesConducted noise Sleep mode Power-management modesActive mode Idle modeEnvironmental specifications Nonoperating vibration VibrationOperating vibration Test for Prominent Discrete Tones PDTs Drive A-weighted Sound Power Levels SWL, BAAcoustics emissions Electromagnetic immunityAnnualized Failure Rate AFR Safety certificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 China Restriction of Hazardous Substances RoHS Directive Environmental protectionCorrosive environment Handling and static-discharge precautions Configuring and mounting the driveSerial ATA cables and connectors Configuring the driveDrive mounting Mounting dimensionsDB35.4 Series Sata Product Manual, Rev. C Hot-Plug compatibility Serial ATA Sata interfacePin Function Definition Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions SignalCommand name Command code in hex Supported ATA commandsSupported ATA commands F4H Word Description Value Identify Device commandXx07H 129 Seagate-reserved Bit Word Description if bit is set to Bit WordSet Features command values Set Features commandCode in features register A.R.T. command 3 S.M.A.R.T. commandsA.R.T. commands Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index ITE Page DB35.4 Series Sata Product Manual, Rev. C Page Seagate Technology LLC

DB35.4 specifications

The Seagate DB35.4 series of hard disk drives (HDDs) represents a significant advancement in data storage solutions for digital video recording and other demanding applications. Designed specifically for use in DVRs, NVRs, and related multimedia production environments, the DB35.4 drives are tailored to meet the rigorous requirements of streaming and recording high-definition video content.

One of the standout features of the DB35.4 series is its optimized design for continuous operation. These drives are built to handle workloads that involve constant read and write cycles, making them ideal for multi-channel recording setups. With a Mean Time Between Failures (MTBF) rating of 1.2 million hours, the drives ensure reliability and durability, essential for critical applications in broadcasting and surveillance.

The DB35.4 series supports advanced technologies, including native command queuing (NCQ), which enhances performance by allowing multiple read and write commands to be processed simultaneously. This results in improved data transfer rates and reduced latency, which are vital for applications requiring swift access to stored content. With capacities ranging from 250 GB to 2 TB, the drives provide ample space for storing extensive video libraries.

In terms of performance, the DB35.4 features a rotational speed of 7200 RPM, combined with a SATA interface that enables high-speed data transfers. The drives usually come equipped with 8 MB or higher cache memory, further boosting their efficiency during heavy data loads. This ensures that users experience smooth playback and recording, minimizing the risk of dropped frames or buffering.

Energy efficiency is another key characteristic of the Seagate DB35.4 series. Designed with power management in mind, these drives consume less energy during operation while still delivering optimal performance. This not only reduces operational costs but also contributes to a more environmentally friendly solution for users looking to maximize their storage capabilities without excessive power consumption.

In summary, the Seagate DB35.4 HDDs stand out for their reliability, performance, and efficiency. With their specialized design for multimedia applications, advanced technologies like NCQ, and a focus on energy savings, the DB35.4 series remains a preferred choice for businesses and individuals aiming to optimize their digital storage solutions in a demanding video-centric world.
Top Page Image Contents