Seagate ST3500416SS, ST31000425SS, ST31000424SS, ST31000426SS Predictive failures, Thermal monitor

Page 25

S.M.A.R.T. measures error rates. All errors for each monitored attribute are recorded. A counter keeps track of the number of errors for the current interval. This counter is referred to as the Failure Counter.

Error rate is the number of errors per operation. The algorithm that S.M.A.R.T. uses to record rates of error is to set thresholds for the number of errors and their interval. If the number of errors exceeds the threshold before the interval expires, the error rate is considered to be unacceptable. If the number of errors does not exceed the threshold before the interval expires, the error rate is considered to be acceptable. In either case, the inter- val and failure counters are reset and the process starts over.

Predictive failures

S.M.A.R.T. signals predictive failures when the drive is performing unacceptably for a period of time. The firm- ware keeps a running count of the number of times the error rate for each attribute is unacceptable. To accom- plish this, a counter is incremented each time the error rate is unacceptable and decremented (not to exceed zero) whenever the error rate is acceptable. If the counter continually increments such that it reaches the pre- dictive threshold, a predictive failure is signaled. This counter is referred to as the Failure History Counter. There is a separate Failure History Counter for each attribute.

6.2.5Thermal monitor

Constellation ES drives implement a temperature warning system which:

1.Signals the host if the temperature exceeds a value which would threaten the drive.

2.Signals the host if the temperature exceeds a user-specified value.

3.Saves a S.M.A.R.T. data frame on the drive which exceeds the threatening temperature value.

A temperature sensor monitors the drive temperature and issues a warning over the interface when the tem- perature exceeds a set threshold. The temperature is measured at power-up and then at ten-minute intervals after power-up.

The thermal monitor system generates a warning code of 01-0B01 when the temperature exceeds the speci- fied limit in compliance with the SCSI standard. The drive temperature is reported in the FRU code field of mode sense data. You can use this information to determine if the warning is due to the temperature exceeding the drive threatening temperature or the user-specified temperature.

This feature is controlled by the Enable Warning (EWasc) bit, and the reporting mechanism is controlled by the Method of Reporting Informational Exceptions field (MRIE) on the Informational Exceptions Control (IEC) mode page (1Ch).

The current algorithm implements two temperature trip points. The first trip point is set at 65°C which is the maximum temperature limit according to the drive specification. The second trip point is user-selectable using the Log Select command. The reference temperature parameter in the temperature log page (see Table 1) can be used to set this trip point. The default value for this drive is 65°C, however, you can set it to any value in the range of 0 to 65°C. If you specify a temperature greater than 65°C in this field, the temperature is rounded down to 65°C. A sense code is sent to the host to indicate the rounding of the parameter field.

Table 1: Temperature Log Page (0Dh)

Parameter Code

Description

 

 

0000h

Primary Temperature

 

 

0001h

Reference Temperature

 

 

Constellation ES Series SAS Product Manual, Rev. E

17

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Standard Models Self-Encrypting Drive Models ST32000446SS ST31000426SS ST3500416SSSED Fips 140-2 Models Revision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPower Constellation ES Series SAS Product Manual, Rev. E List of Figures Constellation ES Series SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlPredictive failures Temperature Log Page 0Dh Parameter Code DescriptionThermal monitor Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesShipping Product warrantyProduct repair and return information PowerChoiceTM power management Physical/electrical specificationsPowerChoice modes DC power requirements AC power requirementsConstellation ES Series SAS Product Manual, Rev. E Constellation ES Series SAS Product Manual, Rev. E Page Power sequencing General DC power requirement notesConducted noise immunity TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation 500GB models in 3Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GBOs per Second 500GB models in 6Gb operation Environmental limits Temperature a. OperatingRelative humidity Shock and vibration Effective altitude sea level a. OperatingShock Recommended mounting Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentElectromagnetic susceptibility Mounting configuration dimensions Mechanical specificationsPurpose About FipsLevel 2 security Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDrive internal defects/errors Defect and error managementDrive error recovery procedures SAS system errors Media Pre-Scan Background Media ScanDeferred Auto-Reallocation Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Inquiry data Mode Sense dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous features Miscellaneous operating features and conditionsMiscellaneous status SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. E Page Seagate Technology LLC

ST3500414SS, ST3500415SS, ST32000445SS, ST31000425SS, ST32000446SS specifications

Seagate, a leader in data storage solutions, has introduced a range of high-capacity and reliable hard drives designed for enterprise environments, including the Seagate ST31000424SS, ST3500416SS, ST31000426SS, ST32000444SS, and ST32000446SS. Each of these models is built with an emphasis on performance, endurance, and advanced data protection technologies, catering to mission-critical applications and data-intensive workloads.

The ST31000424SS is a 1TB drive designed for servers and data centers. It offers a 7,200 RPM spindle speed and a 6 Gb/s SATA interface, ensuring quick data access and transfer rates. With a 64MB cache buffer, the ST31000424SS provides enhanced read/write performance, making it suitable for applications that demand quick responses from the storage subsystem.

Similarly, the ST3500416SS is a high-capacity 500GB model, also spinning at 7,200 RPM with a 6 Gb/s SATA interface. This drive is ideal for mid-range servers and enterprise storage, providing an excellent balance of performance and capacity for users looking to optimize their storage efficiency while maintaining lower power consumption.

The ST31000426SS expands the capacity to 1TB while retaining the same reliability and performance characteristics as its counterparts. Its robust design ensures reliability in multi-drive environments, making it an appealing choice for virtualization and database applications, where performance is critical.

The ST32000444SS and ST32000446SS represent Seagate's commitment to higher capacities, with both offering 2TB of storage. They both feature 7,200 RPM speeds, 6 Gb/s SATA interfaces, and 64MB cache buffers, catering to high-demand environments such as cloud storage and data analytics. The drives also integrate advanced error recovery and data integrity features, ensuring the protection of sensitive data, which is vital for enterprise users.

Each model supports Seagate's PowerChoice technology, which optimizes power consumption without sacrificing performance, enhancing energy efficiency in modern data centers. With a broad range of capacities and performance levels, these Seagate drives provide scalable solutions tailored to meet the robust demands of today’s enterprise applications, ensuring reliability and performance for critical data operations.
Top Page Image Contents