Seagate ST32000446SS, ST31000425SS, ST31000424SS manual AC power requirements, DC power requirements

Page 30

7.1.1PowerChoice reporting methods

PowerChoiceTM provides these reporting methods for tracking purposes:

Request Sense command reports

•Current power condition

•Method of entry

Note. Processing the Request Sense command does not impact the drive’s power save state.

Mode Sense command reports (mode page 0x1A)

•Idle conditions enabled / disabled

•Idle condition timer values (100ms increments) (default, saved, current, changeable)

Power Condition Vital Product Data (VPD) Page (VPD page 0x8A)

•Supported power conditions

•Typical recovery time from power conditions (1ms increments)

Start/Stop Cycle Counter Log Page reports (log page 0x0E)

• Specified and accumulated Start/Stops and Load/Unload cycles

Power Condition Transitions Log Page reports (log page 0x1A, subpage 0x00)

• Accumulated transitions to Active, Idle_A, Idle_B, Idle_C, Standby_Y, Standby_Z

7.2AC power requirements

None.

7.3DC power requirements

The voltage and current requirements for a single drive are shown below. Values indicated apply at the drive connector.

The standard drive models and the SED drive models have identical hardware, however the security and encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in power consumption. There is no additional drain on the 12V supply.

22

Constellation ES Series SAS Product Manual, Rev. E

Page 29 Page 31
Image 30
Page 29 Page 31
Contents ST32000446SS ST31000426SS ST3500416SS Standard Models Self-Encrypting Drive ModelsSED Fips 140-2 Models Revision history Contents About Fips About self-encrypting drives Defect and error managementInstallation Interface requirementsPower Constellation ES Series SAS Product Manual, Rev. E List of Figures Constellation ES Series SAS Product Manual, Rev. E Seagate Technology support services Seagate Online Support and ServicesScope Electromagnetic compatibility Applicable standards and reference documentationStandards Electromagnetic susceptibilityAustralian C-Tick Electromagnetic complianceElectromagnetic compliance for the European Union Korean KCCReference documents European Union Restriction of Hazardous Substances RoHSGeneral description Standard features Media descriptionFormatted capacities PerformanceReliability Programmable drive capacityFactory-installed options Seek performance characteristics Performance characteristicsInternal drive characteristics Access timeGeneral performance characteristics Start/stop timePrefetch/multi-segmented cache control Cache operationCaching write data Prefetch operationRecoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor DST failure definition State of the drive prior to testingDrive Self Test DST ImplementationExtended test Function Code 010b Short and extended testsShort test Function Code 001b Log page entriesProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes AC power requirements DC power requirementsConstellation ES Series SAS Product Manual, Rev. E Constellation ES Series SAS Product Manual, Rev. E Page General DC power requirement notes Power sequencingConducted noise immunity Current profiles TB model current profilesConstellation ES Series SAS Product Manual, Rev. E GB model current profiles Power dissipation 2TB models in 3Gb operation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GB 500GB models in 3Gb operationOs per Second 500GB models in 6Gb operation Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Recommended mounting Acoustics Air cleanlinessVibration a. Operating-normal Corrosive environmentElectromagnetic susceptibility Mechanical specifications Mounting configuration dimensionsAbout Fips PurposeLevel 2 security About self-encrypting drives Controlled accessAdmin SP Data encryptionDrive locking Default passwordRandom number generator RNG Data bandsSupported commands Authenticated firmware downloadPower requirements Cryptographic eraseDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Installation Drive orientationCooling Air flowDrive mounting GroundingSAS features Interface requirementsDual port support Scsi commands supported Supported commandsSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Electrical description Physical characteristicsConnector requirements Pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutDifferential signals SAS-2 Specification ComplianceLED drive signal General interface characteristicsIndex NumericsKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. E Page Seagate Technology LLC

ST3500414SS, ST3500415SS, ST32000445SS, ST31000425SS, ST32000446SS specifications

Seagate, a leader in data storage solutions, has introduced a range of high-capacity and reliable hard drives designed for enterprise environments, including the Seagate ST31000424SS, ST3500416SS, ST31000426SS, ST32000444SS, and ST32000446SS. Each of these models is built with an emphasis on performance, endurance, and advanced data protection technologies, catering to mission-critical applications and data-intensive workloads.

The ST31000424SS is a 1TB drive designed for servers and data centers. It offers a 7,200 RPM spindle speed and a 6 Gb/s SATA interface, ensuring quick data access and transfer rates. With a 64MB cache buffer, the ST31000424SS provides enhanced read/write performance, making it suitable for applications that demand quick responses from the storage subsystem.

Similarly, the ST3500416SS is a high-capacity 500GB model, also spinning at 7,200 RPM with a 6 Gb/s SATA interface. This drive is ideal for mid-range servers and enterprise storage, providing an excellent balance of performance and capacity for users looking to optimize their storage efficiency while maintaining lower power consumption.

The ST31000426SS expands the capacity to 1TB while retaining the same reliability and performance characteristics as its counterparts. Its robust design ensures reliability in multi-drive environments, making it an appealing choice for virtualization and database applications, where performance is critical.

The ST32000444SS and ST32000446SS represent Seagate's commitment to higher capacities, with both offering 2TB of storage. They both feature 7,200 RPM speeds, 6 Gb/s SATA interfaces, and 64MB cache buffers, catering to high-demand environments such as cloud storage and data analytics. The drives also integrate advanced error recovery and data integrity features, ensuring the protection of sensitive data, which is vital for enterprise users.

Each model supports Seagate's PowerChoice technology, which optimizes power consumption without sacrificing performance, enhancing energy efficiency in modern data centers. With a broad range of capacities and performance levels, these Seagate drives provide scalable solutions tailored to meet the robust demands of today’s enterprise applications, ensuring reliability and performance for critical data operations.
Top Page Image Contents