Seagate ST31000425SS Short and extended tests, Short test Function Code 001b, Log page entries

Page 27

6.2.6.2.3Short and extended tests

DST has two testing options:

1.short

2.extended

These testing options are described in the following two subsections.

Each test consists of three segments: an electrical test segment, a servo test segment, and a read/verify scan segment.

Short test (Function Code: 001b)

The purpose of the short test is to provide a time-limited test that tests as much of the drive as possible within 120 seconds. The short test does not scan the entire media surface, but does some fundamental tests and scans portions of the media. A complete read/verify scan is not performed and only factual failures will report a fault condition. This option provides a quick confidence test of the drive.

Extended test (Function Code: 010b)

The objective of the extended test option is to empirically test critical drive components. For example, the seek tests and on-track operations test the positioning mechanism. The read operation tests the read head element and the media surface. The write element is tested through read/write/read operations. The integrity of the media is checked through a read/verify scan of the media. Motor functionality is tested by default as a part of these tests.

The anticipated length of the Extended test is reported through the Control Mode page.

6.2.6.2.4Log page entries

When the drive begins DST, it creates a new entry in the Self-test Results Log page. The new entry is created by inserting a new self-test parameter block at the beginning of the self-test results log parameter section of the log page. Existing data will be moved to make room for the new parameter block. The drive reports 20 param- eter blocks in the log page. If there are more than 20 parameter blocks, the least recent parameter block will be deleted. The new parameter block will be initialized as follows:

1.The Function Code field is set to the same value as sent in the DST command

2.The Self-Test Results Value field is set to Fh

3.The drive will store the log page to non-volatile memory

After a self-test is complete or has been aborted, the drive updates the Self-Test Results Value field in its Self- Test Results Log page in non-volatile memory. The host may use Log Sense to read the results from up to the last 20 self-tests performed by the drive. The self-test results value is a 4-bit field that reports the results of the test. If the field is set to zero, the drive passed with no errors detected by the DST. If the field is not set to zero, the test failed for the reason reported in the field.

The drive will report the failure condition and LBA (if applicable) in the Self-test Results Log parameter. The Sense key, ASC, ASCQ, and FRU are used to report the failure condition.

6.2.6.2.5Abort

There are several ways to abort a diagnostic. You can use a SCSI Bus Reset or a Bus Device Reset message to abort the diagnostic.

You can abort a DST executing in background mode by using the abort code in the DST Function Code field. This will cause a 01 (self-test aborted by the application client) code to appear in the self-test results values log. All other abort mechanisms will be reported as a 02 (self-test routine was interrupted by a reset condition).

Constellation ES Series SAS Product Manual, Rev. E

19

Page 26 Page 28
Image 27
Page 26 Page 28
Contents ST32000446SS ST31000426SS ST3500416SS Standard Models Self-Encrypting Drive ModelsSED Fips 140-2 Models Revision history Contents Interface requirements Defect and error managementInstallation About Fips About self-encrypting drivesPower Constellation ES Series SAS Product Manual, Rev. E List of Figures Constellation ES Series SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesScope Electromagnetic susceptibility Applicable standards and reference documentationStandards Electromagnetic compatibilityKorean KCC Electromagnetic complianceElectromagnetic compliance for the European Union Australian C-TickEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresProgrammable drive capacity PerformanceReliability Formatted capacitiesFactory-installed options Access time Performance characteristicsInternal drive characteristics Seek performance characteristicsStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataUnrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactTemperature Log Page 0Dh Parameter Code Description Predictive failuresThermal monitor Implementation State of the drive prior to testingDrive Self Test DST DST failure definitionLog page entries Short and extended testsShort test Function Code 001b Extended test Function Code 010bProduct warranty ShippingProduct repair and return information Physical/electrical specifications PowerChoiceTM power managementPowerChoice modes DC power requirements AC power requirementsConstellation ES Series SAS Product Manual, Rev. E Constellation ES Series SAS Product Manual, Rev. E Page General DC power requirement notes Power sequencingConducted noise immunity TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GB 500GB models in 3Gb operationOs per Second 500GB models in 6Gb operation Temperature a. Operating Environmental limitsRelative humidity Effective altitude sea level a. Operating Shock and vibrationShock Recommended mounting Corrosive environment Air cleanlinessVibration a. Operating-normal AcousticsElectromagnetic susceptibility Mounting configuration dimensions Mechanical specificationsAbout Fips PurposeLevel 2 security Data encryption Controlled accessAdmin SP About self-encrypting drivesData bands Default passwordRandom number generator RNG Drive lockingCryptographic erase Authenticated firmware downloadPower requirements Supported commandsDefect and error management Drive internal defects/errorsDrive error recovery procedures SAS system errors Background Media Scan Media Pre-ScanDeferred Auto-Reallocation Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Mode Sense data Inquiry dataConstellation ES inquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous operating features and conditions Miscellaneous featuresMiscellaneous status SAS physical interface Datum B Section C C Section a a Pin descriptions Physical characteristicsConnector requirements Electrical descriptionReady LED Out Signal characteristicsPower SAS transmitters and receiversGeneral interface characteristics SAS-2 Specification ComplianceLED drive signal Differential signalsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. E Page Seagate Technology LLC

ST3500414SS, ST3500415SS, ST32000445SS, ST31000425SS, ST32000446SS specifications

Seagate, a leader in data storage solutions, has introduced a range of high-capacity and reliable hard drives designed for enterprise environments, including the Seagate ST31000424SS, ST3500416SS, ST31000426SS, ST32000444SS, and ST32000446SS. Each of these models is built with an emphasis on performance, endurance, and advanced data protection technologies, catering to mission-critical applications and data-intensive workloads.

The ST31000424SS is a 1TB drive designed for servers and data centers. It offers a 7,200 RPM spindle speed and a 6 Gb/s SATA interface, ensuring quick data access and transfer rates. With a 64MB cache buffer, the ST31000424SS provides enhanced read/write performance, making it suitable for applications that demand quick responses from the storage subsystem.

Similarly, the ST3500416SS is a high-capacity 500GB model, also spinning at 7,200 RPM with a 6 Gb/s SATA interface. This drive is ideal for mid-range servers and enterprise storage, providing an excellent balance of performance and capacity for users looking to optimize their storage efficiency while maintaining lower power consumption.

The ST31000426SS expands the capacity to 1TB while retaining the same reliability and performance characteristics as its counterparts. Its robust design ensures reliability in multi-drive environments, making it an appealing choice for virtualization and database applications, where performance is critical.

The ST32000444SS and ST32000446SS represent Seagate's commitment to higher capacities, with both offering 2TB of storage. They both feature 7,200 RPM speeds, 6 Gb/s SATA interfaces, and 64MB cache buffers, catering to high-demand environments such as cloud storage and data analytics. The drives also integrate advanced error recovery and data integrity features, ensuring the protection of sensitive data, which is vital for enterprise users.

Each model supports Seagate's PowerChoice technology, which optimizes power consumption without sacrificing performance, enhancing energy efficiency in modern data centers. With a broad range of capacities and performance levels, these Seagate drives provide scalable solutions tailored to meet the robust demands of today’s enterprise applications, ensuring reliability and performance for critical data operations.
Top Page Image Contents