Seagate ST32000444SS Signal characteristics, SAS transmitters and receivers, Power, Ready LED Out

Page 77

12.4.6SAS transmitters and receivers

A typical SAS differential copper transmitter and receiver pair is shown in Figure 19. The receiver is AC cou- pling to eliminate ground shift noise.

 

TX

Transmitter

Differential

Transfer Medium

100

 

 

TY

Figure 19. SAS transmitters and receivers

.01

.01

RX

Receiver

100

RY

12.4.7Power

The drive receives power (+5 volts and +12 volts) through the SAS device connector.

Three +12 volt pins provide power to the drive, 2 short and 1 long. The current return for the +12 volt power supply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Three +5 volt pins provide power to the drive, 2 short and 1 long. The current return for the +5 volt power sup- ply is through the common ground pins. The supply current and return current must be distributed as evenly as possible among the pins.

Current to the drive through the long power pins may be limited by the system to reduce inrush current to the drive during hot plugging.

12.5Signal characteristics

This section describes the electrical signal characteristics of the drive’s input and output signals. See Table 15 for signal type and signal name information.

12.5.1Ready LED Out

The Ready LED Out signal is driven by the drive as indicated in Table 16.

Table 16: Ready LED Out conditions

Normal command activity

 

LED status

 

 

 

Ready LED Meaning bit mode page 19h

0

 

1

 

 

 

 

Spun down and no activity

Off

 

Off

 

 

 

 

Spun down and activity (command executing)

On

 

On

 

 

 

 

Spun up and no activity

On

 

Off

 

 

 

 

Spun up and activity (command executing)

Off

 

On

 

 

 

 

Spinning up or down

 

Blinks steadily

 

(50% on and 50% off, 0.5 seconds on and off for 0.5 seconds)

 

 

 

Format in progress, each cylinder change

 

Toggles on/off

 

 

 

 

Constellation ES Series SAS Product Manual, Rev. E

69

Image 77
Contents SED Fips 140-2 Models ST32000446SS ST31000426SS ST3500416SSStandard Models Self-Encrypting Drive Models Revision history Contents Installation Defect and error managementAbout Fips About self-encrypting drives Interface requirementsPower Constellation ES Series SAS Product Manual, Rev. E List of Figures Constellation ES Series SAS Product Manual, Rev. E Seagate Online Support and Services Seagate Technology support servicesScope Standards Applicable standards and reference documentationElectromagnetic compatibility Electromagnetic susceptibilityElectromagnetic compliance for the European Union Electromagnetic complianceAustralian C-Tick Korean KCCEuropean Union Restriction of Hazardous Substances RoHS Reference documentsGeneral description Media description Standard featuresReliability PerformanceFormatted capacities Programmable drive capacityFactory-installed options Internal drive characteristics Performance characteristicsSeek performance characteristics Access timeStart/stop time General performance characteristicsCache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenanceControlling S.M.A.R.T 4 S.M.A.R.TPerformance impact Reporting controlThermal monitor Temperature Log Page 0Dh Parameter Code DescriptionPredictive failures Drive Self Test DST State of the drive prior to testingDST failure definition ImplementationShort test Function Code 001b Short and extended testsExtended test Function Code 010b Log page entriesProduct repair and return information Product warrantyShipping PowerChoice modes Physical/electrical specificationsPowerChoiceTM power management DC power requirements AC power requirementsConstellation ES Series SAS Product Manual, Rev. E Constellation ES Series SAS Product Manual, Rev. E Page Conducted noise immunity General DC power requirement notesPower sequencing TB model current profiles Current profilesConstellation ES Series SAS Product Manual, Rev. E GB model current profiles 2TB models in 3Gb operation Power dissipation2TB models in 6Gb operation 1TB models in 3Gb operation 1TB models in 6Gb operation Os per Second ST3500414SS CURRENT/POWER vs Throughput SAS 3.0GB500GB models in 3Gb operation 500GB models in 6Gb operation Relative humidity Temperature a. OperatingEnvironmental limits Shock Effective altitude sea level a. OperatingShock and vibration Recommended mounting Vibration a. Operating-normal Air cleanlinessAcoustics Corrosive environmentElectromagnetic susceptibility Mounting configuration dimensions Mechanical specificationsLevel 2 security About FipsPurpose Admin SP Controlled accessAbout self-encrypting drives Data encryptionRandom number generator RNG Default passwordDrive locking Data bandsPower requirements Authenticated firmware downloadSupported commands Cryptographic eraseDrive error recovery procedures Defect and error managementDrive internal defects/errors SAS system errors Deferred Auto-Reallocation Background Media ScanMedia Pre-Scan Idle Read After Write Drive orientation InstallationAir flow CoolingGrounding Drive mountingInterface requirements SAS featuresDual port support Supported commands Scsi commands supportedSupported commands Supported commands Supported commands Constellation ES inquiry data Mode Sense dataInquiry data Page Mode Sense data changeable and default values for 2TB drives Mode Sense data changeable and default values for 1TB drives 3a 38 60 30 00 00 02 Miscellaneous status Miscellaneous operating features and conditionsMiscellaneous features SAS physical interface Datum B Section C C Section a a Connector requirements Physical characteristicsElectrical description Pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutLED drive signal SAS-2 Specification ComplianceDifferential signals General interface characteristicsNumerics IndexKCC Msid Mtbf See also cooling Page Constellation ES Series SAS Product Manual, Rev. E Page Seagate Technology LLC

ST3500414SS, ST3500415SS, ST32000445SS, ST31000425SS, ST32000446SS specifications

Seagate, a leader in data storage solutions, has introduced a range of high-capacity and reliable hard drives designed for enterprise environments, including the Seagate ST31000424SS, ST3500416SS, ST31000426SS, ST32000444SS, and ST32000446SS. Each of these models is built with an emphasis on performance, endurance, and advanced data protection technologies, catering to mission-critical applications and data-intensive workloads.

The ST31000424SS is a 1TB drive designed for servers and data centers. It offers a 7,200 RPM spindle speed and a 6 Gb/s SATA interface, ensuring quick data access and transfer rates. With a 64MB cache buffer, the ST31000424SS provides enhanced read/write performance, making it suitable for applications that demand quick responses from the storage subsystem.

Similarly, the ST3500416SS is a high-capacity 500GB model, also spinning at 7,200 RPM with a 6 Gb/s SATA interface. This drive is ideal for mid-range servers and enterprise storage, providing an excellent balance of performance and capacity for users looking to optimize their storage efficiency while maintaining lower power consumption.

The ST31000426SS expands the capacity to 1TB while retaining the same reliability and performance characteristics as its counterparts. Its robust design ensures reliability in multi-drive environments, making it an appealing choice for virtualization and database applications, where performance is critical.

The ST32000444SS and ST32000446SS represent Seagate's commitment to higher capacities, with both offering 2TB of storage. They both feature 7,200 RPM speeds, 6 Gb/s SATA interfaces, and 64MB cache buffers, catering to high-demand environments such as cloud storage and data analytics. The drives also integrate advanced error recovery and data integrity features, ensuring the protection of sensitive data, which is vital for enterprise users.

Each model supports Seagate's PowerChoice technology, which optimizes power consumption without sacrificing performance, enhancing energy efficiency in modern data centers. With a broad range of capacities and performance levels, these Seagate drives provide scalable solutions tailored to meet the robust demands of today’s enterprise applications, ensuring reliability and performance for critical data operations.