Seagate 7200.8 PATA manual Reliability, Agency certification, Safety certification, Korean RRL

Page 24

2.12

Reliability

 

 

 

Nonrecoverable read errors

1 per 1014 bits read, max.

Annualized Failure Rate (AFR)

0.34% (nominal power, 25°C ambient temperature)

 

 

Contact start-stop cycles

50,000 cycles

 

 

(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)

 

 

Service Life

5 Years

 

 

 

Warranty

 

5 years on distribution units.

 

 

To determine the warranty for a specific drive, use a web browser to access the fol-

 

 

lowing web page:

 

 

www.seagate.com/support/service/

 

 

From this page, click on the “Verify Your Warranty” link. You will be asked to provide

 

 

the drive serial number, model number (or part number) and country of purchase.

 

 

The system will display the warranty information for your drive.

 

 

Preventive maintenance

None required

 

 

 

2.13Agency certification

2.13.1Safety certification

The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America.

2.13.2Electromagnetic compatibility

Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec- tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and the immunity levels are defined by EN 55024.

Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the directives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should confirm EMC compliance and provide CE marking for their products.

Korean RRL

If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para- graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information and Communication Republic of Korea.

18

Barracuda 7200.8 PATA Product Manual, Rev. F

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Barracuda 7200.8 Pata Page Contents Barracuda 7200.8 Pata Product Manual, Rev. F List of Figures Barracuda 7200.8 Pata Product Manual, Rev. F Introduction Barracuda 7200.8 PataBarracuda 7200.8 Pata Product Manual, Rev. F Drive specifications Specification summary tableDrive specifications for 400 Gbyte models Drive specification ST3400832A ST3400632ABarracuda 7200.8 Pata Product Manual, Rev. F Drive specifications for 300 Gbyte models Drive specification ST3300831A ST3300631AFollowing web Drive specifications for 250 and 200 Gbyte models Drive specification ST3250823A ST3250623A ST3200826ABarracuda 7200.8 Pata Product Manual, Rev. F Default logical geometry LBA modeFormatted capacity Recording and interface technologyPhysical characteristics Seek timeStart/stop times Power specifications Typical current profile Conducted noiseVoltage tolerance Power-management modes Active modeIdle mode Sleep modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityFluid Dynamic Bearing FDB motor acoustics Radio frequency environmentsSafety certification ReliabilityAgency certification Electromagnetic compatibilityAustralian C-Tick N176 FCC verificationEnvironmental protection Corrosive environmentEuropean Union Restriction of Hazardous Substances RoHS Configuring and mounting the drive Handling and static discharge precautionsBreather filter hole precautions Breather filter hole locationJumper settings Master/slave configurationDrive as master with a non-ATA-compatible slave Cable-select optionDrive mounting Ultra ATA/100 cableMounting dimensions-top, side and end view Barracuda 7200.8 Pata Product Manual, Rev. F ATA interface signals and connector pins ATA interfaceSupported ATA commands Command name Command code in hexF4H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Set Features command 4 S.M.A.R.T. commandsCode in features Register A.R.T. command Seagate Technology support services InternetPresales Support Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index Page TMR Barracuda 7200.8 Pata Product Manual, Rev. F Page Seagate Technology LLC
Top Page Image Contents