Seagate ST3250623A, 7200.8 PATA Jumper settings, Master/slave configuration, Cable-select option

Page 29

3.3Jumper settings

3.3.1Master/slave configuration

The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave.

Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8.

Drive as slave. Remove all jumpers.

Drive as master with a non-ATA-compatible slave.

Use this jumper setting only if the drive does not work as a master with no jumpers installed.

Options jumper block

Master or single drive

Drive is slave

Master with non ATA- compatible slave

Cable select

Limit drive capacity to 32 Gbytes

7 5 3 1

8 6 4 2

Circuit Board

Figure 4 Master/slave jumper settings

3.3.2Cable-select option

Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to determine whether your computer supports this option.

3.3.3Alternate capacity jumper

Some older computers may “hang” at startup if their BIOS detects a disc drive with a capacity greater than 32 Gbytes. This limits the drive’s capacity to 32 Gbytes when the alternate capacity jumper is used. To access the full capacity of the drive, you can:

•Update the BIOS

•Use third-party software such as DiscWizard™ or Disk Manager

•Use a third-party host adapter

For drives with capacities greater than 32 Gbytes, the alternate capacity jumper changes the total available LBA sectors to 32 Gbytes to solve issues with some BIOS during power on. The ATA Set Features subcom- mand “F1H Report Full Capacity Available” causes Identify Data words 60 and 61 to report the full capacity. See Section 4.1.3 on page 33 for more details on the Set Features command.

Windows XP, Windows Me, Windows 98 or newer versions are needed to support drives with capacities greater than 32 Gbytes.

Barracuda 7200.8 PATA Product Manual, Rev. F

23

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Barracuda 7200.8 Pata Page Contents Barracuda 7200.8 Pata Product Manual, Rev. F List of Figures Barracuda 7200.8 Pata Product Manual, Rev. F Barracuda 7200.8 Pata IntroductionBarracuda 7200.8 Pata Product Manual, Rev. F Specification summary table Drive specificationsDrive specification ST3400832A ST3400632A Drive specifications for 400 Gbyte modelsBarracuda 7200.8 Pata Product Manual, Rev. F Drive specification ST3300831A ST3300631A Drive specifications for 300 Gbyte modelsFollowing web Drive specification ST3250823A ST3250623A ST3200826A Drive specifications for 250 and 200 Gbyte modelsBarracuda 7200.8 Pata Product Manual, Rev. F LBA mode Default logical geometryFormatted capacity Recording and interface technologyStart/stop times Physical characteristicsSeek time Power specifications Voltage tolerance Typical current profileConducted noise Active mode Power-management modesIdle mode Sleep modeEnvironmental specifications Operating shock ShockNonoperating shock VibrationElectromagnetic immunity AcousticsFluid Dynamic Bearing FDB motor acoustics Radio frequency environmentsReliability Safety certificationAgency certification Electromagnetic compatibilityFCC verification Australian C-Tick N176European Union Restriction of Hazardous Substances RoHS Environmental protectionCorrosive environment Handling and static discharge precautions Configuring and mounting the driveBreather filter hole location Breather filter hole precautionsMaster/slave configuration Jumper settingsDrive as master with a non-ATA-compatible slave Cable-select optionUltra ATA/100 cable Drive mountingMounting dimensions-top, side and end view Barracuda 7200.8 Pata Product Manual, Rev. F ATA interface ATA interface signals and connector pinsCommand name Command code in hex Supported ATA commandsF4H Word Description Value Identify Device commandXx07H Description if bit is set to Bit Word 4 S.M.A.R.T. commands Set Features commandCode in features Register A.R.T. command Internet Seagate Technology support servicesPresales Support Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index Page TMR Barracuda 7200.8 Pata Product Manual, Rev. F Page Seagate Technology LLC
Top Page Image Contents