Seagate ST93015A manual Shock, Operating shock, Nonoperating shock, Vibration, Operating vibration

Page 22

2.10.5Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

2.10.5.1Operating shock

These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 225 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.

2.10.5.2Nonoperating shock

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 800 Gs based on a nonrepetitive half-sine shock pulse of 1 msec duration.

The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 400 Gs based on a nonrepetitive half-sine shock pulse of 0.5 msec duration.

2.10.6Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.10.6.1Operating vibration

The following table lists the maximum vibration levels that the drive may experience while meeting the perfor- mance standards specified in this document.

5–500 Hz 1.0 Gs (0 to peak). Max displacement may apply below 10 Hz.

2.10.6.2Nonoperating vibration

The following table lists the maximum nonoperating vibration that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation.

5–500 Hz 5.0 Gs (0 to peak). Max displacement may apply below 22 Hz.

12	Momentus 42 Product Manual, Rev. A

Image 22

Contents Momentus Page Momentus Page Rev. a 05/03/2004 All Revision status summary sheetRevision Date Sheets Affected Page Contents Momentus 42 Product Manual, Rev. a List of Figures Viii Momentus 42 Product Manual, Rev. a Introduction Momentus 42 disc driveMomentus 42 Product Manual, Rev. a Specifications Drive specificationsSpecification summary Drive specification ST94019A ST93015A ST92014ASpecifications Formatted capacity Default logical geometryLBA mode Physical organizationTechnology Specification Physical characteristicsRecording and interface technology Typical seek times msec Read Write Seek timeTime to ready Time to ready Typical MaxPower specifications Conducted noise Typical current profileVoltage tolerance Active mode Power-management modesPower management modes Idle modeEnvironmental specifications Nonoperating shock ShockOperating shock VibrationDrive level acoustics AcousticsElectromagnetic immunity Electromagnetic immunityReliability Safety certificationMeasurement type Specification Agency certificationAustralian C-Tick N176 Korean RRLFCC verification Momentus 42 Product Manual, Rev. a Jumper settings Configuring and mounting the driveHandling and static discharge precautions Master/slave configurationDrive mounting Cable-select optionConnector Cable Signal Name Contact Conductor ATA interface signals and connector pinsConnector signals Cable Connector Conductor Contact Signal NameSupported commands Supported ATA commandsCommand name Command code in hex ATA-standard commands ATA-standard power-management commands Command name Command code in hexATA-standard security commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Set Features command Features register valuesSupported S.M.A.R.T. commands 4 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Technical SupportWarranty Service Authorized Service CentersAmericas SEAGATE2 +1-405-324-47003 +1-405-324-4702 Call Center Toll-free Direct dialAmericas +1-405-324-47301 +1-405-324-4704 Call Center Toll-free Direct dial FAX / InternetCall Center Presales and Technical Support Warranty Service FAX Services-All Europe toll callToll-Free Support Numbers Asia/Pacific Support Services Momentus 42 Product Manual, Rev. a Index NumericsPage Page Momentus 42 Product Manual, Rev. a Page Seagate Technology LLC