Seagate ST92014A, ST94019A, ST93015A manual Identify Device command, Word Description Value

Page 32

Table 7: Supported commands (Continued)

Command name

Command code (in hex)

 

 

Security Freeze Lock

F5H

 

 

Security Disable Password

F6H

 

 

4.1.2Identify Device command

The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.

The following commands contain drive-specific features that may not be included in the Draft ATA-6 Standard.

Word

Description

Value

 

 

 

 

Configuration information:

0C5AH

 

• Bit 15: 0 = ATA; 1 = ATAPI

 

0

• Bit 7: removable media

 

 

• Bit 6: removable controller

 

 

• Bit 0: reserved

 

 

 

 

1

Number of logical cylinders

16,383

 

 

 

2

ATA-reserved

0000H

 

 

 

3

Number of logical heads

16

 

 

 

4

Retired

0000H

 

 

 

5

Retired

0000H

 

 

 

6

Number of logical sectors per logical track: 63

003FH

 

 

 

7–9

Retired

0000H

 

 

 

10–19

Serial number: (20 ASCII characters, 0000H = none)

ASCII

 

 

 

20

Retired

0000H

 

 

 

21

Retired

0400H

 

 

 

22

Obsolete

0000H

 

 

 

23–26

Firmware revision

x.xx

 

(8 ASCII character string, padded with blanks to end of string)

 

 

 

 

27–46

Drive model number: (40 ASCII characters, padded with blanks to end of

ST94019A

 

string)

ST93015A

 

 

ST92014A

 

 

 

47

(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write mul-

8010H

 

tiple (16)

 

 

 

 

48

Reserved

0000H

 

 

 

49

Standard Standby timer, IORDY supported and may be disabled

2F00H

 

 

 

50

ATA-reserved

0000H

 

 

 

51

PIO data-transfer cycle timing mode

0200H

 

 

 

52

Retired

0200H

 

 

 

53

Words 54–58, 64–70 and 88 are valid

0007H

 

 

 

22

Momentus 42 Product Manual, Rev. A

Image 32
Contents Momentus Page Momentus Page Revision Date Sheets Affected Revision status summary sheetRev. a 05/03/2004 All Page Contents Momentus 42 Product Manual, Rev. a List of Figures Viii Momentus 42 Product Manual, Rev. a Introduction Momentus 42 disc driveMomentus 42 Product Manual, Rev. a Drive specifications Specification summarySpecifications Drive specification ST94019A ST93015A ST92014ASpecifications Default logical geometry LBA modeFormatted capacity Physical organizationRecording and interface technology Physical characteristicsTechnology Specification Seek time Time to readyTypical seek times msec Read Write Time to ready Typical MaxPower specifications Voltage tolerance Typical current profileConducted noise Power-management modes Power management modesActive mode Idle modeEnvironmental specifications Shock Operating shockNonoperating shock VibrationAcoustics Electromagnetic immunityDrive level acoustics Electromagnetic immunitySafety certification Measurement type SpecificationReliability Agency certificationFCC verification Korean RRLAustralian C-Tick N176 Momentus 42 Product Manual, Rev. a Configuring and mounting the drive Handling and static discharge precautionsJumper settings Master/slave configurationDrive mounting Cable-select optionATA interface signals and connector pins Connector signalsConnector Cable Signal Name Contact Conductor Cable Connector Conductor Contact Signal NameCommand name Command code in hex ATA-standard commands Supported ATA commandsSupported commands ATA-standard security commands Command name Command code in hexATA-standard power-management commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Set Features command Features register valuesCode in features register A.R.T. command 4 S.M.A.R.T. commandsSupported S.M.A.R.T. commands Seagate Technology support services Internet MySeagate Reseller.seagate.comPresales Support Technical SupportWarranty Service Authorized Service CentersCall Center Toll-free Direct dial Americas +1-405-324-47301 +1-405-324-4704Americas SEAGATE2 +1-405-324-47003 +1-405-324-4702 Call Center Toll-free Direct dial FAX / InternetToll-Free Support Numbers FAX Services-All Europe toll callCall Center Presales and Technical Support Warranty Service Asia/Pacific Support Services Momentus 42 Product Manual, Rev. a Index NumericsPage Page Momentus 42 Product Manual, Rev. a Page Seagate Technology LLC