Seagate ST94019A Configuring and mounting the drive, Handling and static discharge precautions

Page 27

3.0Configuring and mounting the drive

This section contains the specifications and instructions for configuring and mounting the drive.

3.1Handling and static discharge precautions

After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis- charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:

Caution:

•Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s exposure to ESD.

•Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure.

•Handle the drive only by its edges or frame.

•The drive is fragile—handle it with care. Do not press down on the drive top cover.

•Always rest the drive on a padded, antistatic surface until you mount it in the computer.

•Do not touch the connector pins or the printed circuit board.

•Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.

3.2Jumper settings

3.2.1Master/slave configuration

Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the 4- pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3.2.2.

The “Master or single drive” option is the factory default setting.

Drive is master (or single drive)

Drive is slave

Cable select

Figure 3. Jumper settings

Momentus 42 Product Manual, Rev. A

17

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Momentus Page Momentus Page Revision status summary sheet Rev. a 05/03/2004 AllRevision Date Sheets Affected Page Contents Momentus 42 Product Manual, Rev. a List of Figures Viii Momentus 42 Product Manual, Rev. a Momentus 42 disc drive IntroductionMomentus 42 Product Manual, Rev. a Drive specification ST94019A ST93015A ST92014A Drive specificationsSpecification summary SpecificationsSpecifications Physical organization Default logical geometryLBA mode Formatted capacityPhysical characteristics Technology SpecificationRecording and interface technology Time to ready Typical Max Seek timeTime to ready Typical seek times msec Read WritePower specifications Typical current profile Conducted noiseVoltage tolerance Idle mode Power-management modesPower management modes Active modeEnvironmental specifications Vibration ShockOperating shock Nonoperating shockElectromagnetic immunity AcousticsElectromagnetic immunity Drive level acousticsAgency certification Safety certificationMeasurement type Specification ReliabilityKorean RRL Australian C-Tick N176FCC verification Momentus 42 Product Manual, Rev. a Master/slave configuration Configuring and mounting the driveHandling and static discharge precautions Jumper settingsCable-select option Drive mountingCable Connector Conductor Contact Signal Name ATA interface signals and connector pinsConnector signals Connector Cable Signal Name Contact ConductorSupported ATA commands Supported commandsCommand name Command code in hex ATA-standard commands Command name Command code in hex ATA-standard power-management commandsATA-standard security commands Word Description Value Identify Device commandXxxxH Description if bit is set to Bit Features register values Set Features command4 S.M.A.R.T. commands Supported S.M.A.R.T. commandsCode in features register A.R.T. command Technical Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Presales SupportAuthorized Service Centers Warranty ServiceCall Center Toll-free Direct dial FAX / Internet Call Center Toll-free Direct dialAmericas +1-405-324-47301 +1-405-324-4704 Americas SEAGATE2 +1-405-324-47003 +1-405-324-4702FAX Services-All Europe toll call Call Center Presales and Technical Support Warranty ServiceToll-Free Support Numbers Asia/Pacific Support Services Momentus 42 Product Manual, Rev. a Numerics IndexPage Page Momentus 42 Product Manual, Rev. a Page Seagate Technology LLC
Top Page Image Contents