Seagate ST93015A, ST94019A, ST92014A manual Description if bit is set to Bit

Page 34

Word	Description	Value

129–	Seagate-reserved	xxxxH
159

160–	ATA-reserved	0000H
254

255	Integrity word	xxA5H

Note. See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data.

Description (if bit is set to 1)

Bit

Word 63

0Multiword DMA mode 0 is supported.

1Multiword DMA mode 1 is supported.

2Multiword DMA mode 2 is supported.

8Multiword DMA mode 0 is currently active.

9Multiword DMA mode 1 is currently active.

10Multiword DMA mode 2 is currently active.

Bit

Word 88

0Ultra DMA mode 0 is supported.

1Ultra DMA mode 1 is supported.

2Ultra DMA mode 2 is supported.

3Ultra DMA mode 3 is supported.

4Ultra DMA mode 4 is supported.

8Ultra DMA mode 0 is currently active.

9Ultra DMA mode 1 is currently active.

10Ultra DMA mode 2 is currently active.

11Ultra DMA mode 3 is currently active.

12Ultra DMA mode 4 is currently active.

13Ultra DMA mode 5 is currently active.

Bit

Word 93

131 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below VIL

24	Momentus 42 Product Manual, Rev. A

Image 34

Contents Momentus Page Momentus Page Rev. a 05/03/2004 All Revision status summary sheetRevision Date Sheets Affected Page Contents Momentus 42 Product Manual, Rev. a List of Figures Viii Momentus 42 Product Manual, Rev. a Introduction Momentus 42 disc driveMomentus 42 Product Manual, Rev. a Specifications Drive specificationsSpecification summary Drive specification ST94019A ST93015A ST92014ASpecifications Formatted capacity Default logical geometryLBA mode Physical organizationTechnology Specification Physical characteristicsRecording and interface technology Typical seek times msec Read Write Seek timeTime to ready Time to ready Typical MaxPower specifications Conducted noise Typical current profileVoltage tolerance Active mode Power-management modesPower management modes Idle modeEnvironmental specifications Nonoperating shock ShockOperating shock VibrationDrive level acoustics AcousticsElectromagnetic immunity Electromagnetic immunityReliability Safety certificationMeasurement type Specification Agency certificationAustralian C-Tick N176 Korean RRLFCC verification Momentus 42 Product Manual, Rev. a Jumper settings Configuring and mounting the driveHandling and static discharge precautions Master/slave configurationDrive mounting Cable-select optionConnector Cable Signal Name Contact Conductor ATA interface signals and connector pinsConnector signals Cable Connector Conductor Contact Signal NameSupported commands Supported ATA commandsCommand name Command code in hex ATA-standard commands ATA-standard power-management commands Command name Command code in hexATA-standard security commands Identify Device command Word Description ValueXxxxH Description if bit is set to Bit Set Features command Features register valuesSupported S.M.A.R.T. commands 4 S.M.A.R.T. commandsCode in features register A.R.T. command Presales Support Seagate Technology support servicesInternet MySeagate Reseller.seagate.com Technical SupportWarranty Service Authorized Service CentersAmericas SEAGATE2 +1-405-324-47003 +1-405-324-4702 Call Center Toll-free Direct dialAmericas +1-405-324-47301 +1-405-324-4704 Call Center Toll-free Direct dial FAX / InternetCall Center Presales and Technical Support Warranty Service FAX Services-All Europe toll callToll-Free Support Numbers Asia/Pacific Support Services Momentus 42 Product Manual, Rev. a Index NumericsPage Page Momentus 42 Product Manual, Rev. a Page Seagate Technology LLC