Seagate ST3300555SS Temperature Log Page 0Dh, Parameter Code Description, Primary Temperature

Page 25

be used to set this trip point. The default value for this drive is 68°C, however, you can set it to any value in the range of 0 to 68°C. If you specify a temperature greater than 68°C in this field, the temperature is rounded down to 68°C. A sense code is sent to the host to indicate the rounding of the parameter field.

Table 1:

Temperature Log Page (0Dh)

 

 

Parameter Code

Description

 

 

 

0000h

 

Primary Temperature

 

 

 

0001h

 

Reference Temperature

 

 

 

5.2.6Drive Self Test (DST)

Drive Self Test (DST) is a technology designed to recognize drive fault conditions that qualify the drive as a failed unit. DST validates the functionality of the drive at a system level.

There are two test coverage options implemented in DST:

1.Extended test

2.Short text

The most thorough option is the extended test that performs various tests on the drive and scans every logical block address (LBA) of the drive. The short test is time-restricted and limited in length—it does not scan the entire media surface, but does some fundamental tests and scans portions of the media.

If DST encounters an error during either of these tests, it reports a fault condition. If the drive fails the test, remove it from service and return it to Seagate for service.

5.2.6.1DST failure definition

The drive will present a “diagnostic failed” condition through the self-tests results value of the diagnostic log page if a functional failure is encountered during DST. The channel and servo parameters are not modified to test the drive more stringently, and the number of retries are not reduced. All retries and recovery processes are enabled during the test. If data is recoverable, no failure condition will be reported regardless of the number of retries required to recover the data.

The following conditions are considered DST failure conditions:

•Seek error after retries are exhausted

•Track-follow error after retries are exhausted

•Read error after retries are exhausted

•Write error after retries are exhausted

Recovered errors will not be reported as diagnostic failures.

5.2.6.2Implementation

This section provides all of the information necessary to implement the DST function on this drive.

Cheetah T10 SAS Product Manual, Rev. A

19

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Cheetah T10 SAS Page Contents Installation Defect and error managementSeagate Technology support services Interface requirementsList of Figures Cheetah T10 SAS Product Manual, Rev. a Cheetah T10 SAS disc drive ScopeCheetah T10 SAS Product Manual, Rev. a Standards Standards, compliance and reference documentsElectromagnetic compatibility Electromagnetic susceptibilityCompliance Reference documents Cheetah T10 SAS Product Manual, Rev. a General description Media description Standard featuresPerformance Reliability Factory-installed accessoriesFormatted capacities Programmable drive capacityUser-installed accessories Options factory installedInternal drive characteristics Performance characteristicsAccess time Seek timeGeneral performance characteristics Format command execution time minutesStart/stop time Cache operation Prefetch/multi-segmented cache controlPrefetch operation Caching write dataError rates Reliability specificationsRecoverable Errors Unrecoverable ErrorsSeek errors Reliability and serviceInterface errors Preventive maintenance4 S.M.A.R.T Hot plugging the driveControlling S.M.A.R.T Performance impactDetermining rate Reporting controlPredictive failures Thermal monitorPrimary Temperature Temperature Log Page 0DhReference Temperature Parameter Code DescriptionInvoking DST State of the drive prior to testingShort and extended tests Short test Function Code 001bAbort Product warrantyShipping Product repair and return informationCheetah T10 SAS Product Manual, Rev. a AC power requirements Physical/electrical specificationsDC power requirements ST3300555SS DC power requirementsST373355SS DC power requirements ST3146755SS DC power requirementsST3146755SS Gbit mode Amps ST373355SS Gbit mode AmpsPower sequencing General DC power requirement notesConducted noise immunity Current profilesTypical ST3300555SS drive current profiles Typical ST3146755SS drive current profiles Typical ST373355SS drive current profiles ST3300555SS in 3 Gbit operation Power dissipationST3300555SS in 1.5 Gbit operation ST3146755SS in 1.5 Gbit operation ST3146755SS in 3 Gbit operationST373355SS in 1.5 Gbit operation ST373355SS in 3 Gbit operationEnvironmental limits Temperature a. OperatingEffective altitude sea level a. Operating Relative humidityShock and vibration ShockRecommended mounting Package size Packaged/product weight Drop heightVibration a. Operating-normal Air cleanlinessCorrosive environment Acoustics Mechanical specificationsDrive internal defects/errors Defect and error managementDrive error recovery procedures Write retry count LBA cumulative, msec Background Media Scan SAS system errorsMedia Pre-Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah T10 SAS Product Manual, Rev. a Interface requirements SAS featuresDual port support Commands supported by Cheetah T10 SAS family drives Scsi commands supportedCommand name Command code Supported Commands supported by Cheetah T10 SAS family drives Commands supported by Cheetah T10 SAS family drives Commands supported by Cheetah T10 SAS family drives Inquiry data Mode Sense dataCheetah T10 SAS inquiry data Bytes Data hexPage Mode Pages ST3300555SS Mode Sense dataST3146755SS Mode Sense data ST373355SS Mode Sense data Miscellaneous features Miscellaneous operating features and conditionsSupported Feature or condition Miscellaneous statusSAS physical interface Datum B Connector requirements Physical characteristicsElectrical description Pin Signal name Signal typePin descriptions SAS pin descriptionsPower Signal characteristicsSAS transmitters and receivers Ready LED OutDifferential signals LED drive signalGeneral interface characteristics Eye masks Eye masks overviewJitter tolerance masks Receive eye maskAbsolute amplitude Normalized time in UISinusoidal Peak-toJitter Frequency in kHzSignal characteristica Units Gbps Transmitter signal characteristicsSignal characteristic Units Gbps Receiver signal characteristicsMaximum allowable jitter Gbps m, n Deterministic jitterqReceiver jitter tolerance Impedance specificationsCompliant jitter test pattern Cjtpat Impedance requirements Sheet 1Impedance requirements Sheet 2 Transmitter characteristicsElectrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah T10 SAS Product Manual, Rev. a Warranty Service Seagate Technology support servicesInternet MySeagate Spp.seagate.com Presales SupportData Recovery Services Data Recovery Services Authorized Service CentersCall center Presales and Technical Support Warranty Service FAX services-All Europe toll callToll-free support numbers Africa/Middle East support services Numerics IndexPage SAS See also cooling Page Seagate Technology LLC

ST3300555SS, ST3146755SS, ST373355SS specifications

The Seagate ST373355SS, ST3146755SS, and ST3300555SS represent a range of high-performance hard drives designed for enterprise applications, particularly in server environments requiring reliability, speed, and high capacity.

The ST373355SS is a 73.5 GB SCSI hard drive operating at 15,000 RPM, which ensures rapid data access and superior performance, making it ideal for transactional applications and data-intensive tasks. With its 4 MB cache, the drive leverages fast read and write speeds, enhancing overall system responsiveness. The SCSI interface, operating at 80 MB/s, allows for high-speed data transfers, making it a suitable choice for demanding environments where quick access to information is critical. Its hot-swappable feature enables maintenance without shutting down the system, maximizing uptime and productivity.

The ST3146755SS, with a capacity of 146.8 GB, builds on the performance of its predecessor while introducing improvements in data handling and reliability. Operating at the same impressive 15,000 RPM, this model also features a 16 MB cache that greatly improves data throughput and access speed. The drive is designed to reduce latency, which is crucial for applications where timing is everything. It is equipped with advanced error recovery features and Seagate’s innovative PowerTrim technology, which improves power efficiency during read and write operations. The ST3146755SS also features a higher mean time between failures (MTBF), underscoring its reliability in high-demand environments.

Lastly, the ST3300555SS offers even greater capacity with 300 GB. This drive maintains the 15,000 RPM rotation speed and benefits from a 16 MB cache, providing a balance of speed and storage capacity. Its advanced SCSI interface supports not just speed but also data integrity, ensuring consistent performance during extensive data transfers. The drive is designed to handle workloads naturally associated with enterprise servers, data warehouses, and video editing applications. Its rugged build supports continuous operation and is tested for high-temperature environments to ensure durability.

In summary, the Seagate ST373355SS, ST3146755SS, and ST3300555SS hard drives are engineered for enterprise environments, combining impressive RPM speeds, significant storage capacities, and advanced technologies to deliver reliability, performance, and efficiency for critical applications. These hard drives represent Seagate's commitment to providing solutions that meet the rigorous demands of modern data environments.
Top Page Image Contents