Seagate ST3400755SS manual Start/stop time, Format command execution time minutes

Page 18

4.2.2Format command execution time (minutes)

 

ST3400755SS

Maximum (with verify)

180

Maximum (without verify)

100

Execution time measured from receipt of the last byte of the Command Descriptor Block (CDB) to the request for a Status Byte Transfer to the Initiator (excluding connect/disconnect).

4.2.3

General performance characteristics

 

Sustainable disk transfer rate*:

 

Minimum

54 Mbytes/sec

Maximum

97 Mbytes/sec

SAS Interface maximum instantaneous transfer rate

300 Mbytes/sec* per port

 

 

(dual port = 600 Mbytes/sec*)

Logical block sizes

 

Default is 512-byte data blocks

 

Sector sizes variable to 512, 520, 524, and 528 kbytes.

 

Read/write consecutive sectors on a track

Yes

Flaw reallocation performance impact (for flaws reallocated at format time using

Negligible

the spare sectors per sparing zone reallocation scheme.)

 

*Assumes no errors and no relocated logical blocks. Rate measured from the start of the first logical block transfer to or from the host.

4.3Start/stop time

The drive accepts the commands listed in the SAS Interface Manual less than 3 seconds after DC power has been applied.

If the drive receives a NOTIFY (ENABLE SPINUP) primitive through either port and has not received a START STOP UNIT command with the START bit equal to 0, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit equal to 0 before receiving a NOTIFY (ENABLE SPINUP) primitive, the drive waits for a START STOP UNIT command with the START bit equal to 1. After receiving a START STOP UNIT command with the START bit equal to 1, the drive waits for a NOTIFY (ENABLE SPINUP) primitive. After receiving a NOTIFY (ENABLE SPINUP) primitive through either port, the drive becomes ready for normal operations within 30 seconds (excluding the error recovery procedure).

If the drive receives a START STOP UNIT command with the START bit and IMMED bit equal to 1 and does not receive a NOTIFY (ENABLE SPINUP) primitive within 5 seconds, the drive fails the START STOP UNIT command.

The START STOP UNIT command may be used to command the drive to stop the spindle. Stop time is 30 sec- onds (maximum) from removal of DC power.

There is no power control switch on the drive.

12

Cheetah NS SAS Product Manual, Rev. B

Image 18
Contents Cheetah NS SAS ST3400755SSPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Typical ST3400755SS drive +5V and +12V current profilesCheetah NS SAS Product Manual, Rev. B Scope Cheetah NS SAS Product Manual, Rev. B Electromagnetic compatibility Standards, compliance and reference documentsStandards Electromagnetic susceptibilityCompliance Reference documents Cheetah NS SAS Product Manual, Rev. B General description Performance Standard featuresMedia description ReliabilityProgrammable drive capacity Factory-installed optionsFormatted capacities ST3400755SSCheetah NS SAS Product Manual, Rev. B Access time Performance characteristicsInternal drive characteristics Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor Implementation State of the drive prior to testingDST failure definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationCheetah NS SAS Product Manual, Rev. B DC power requirements Physical/electrical specificationsAC power requirements ST3400755SS DC power requirementsConducted noise immunity General DC power requirement notesPower sequencing Current profilesPower dissipation Typical ST3400755SS drive +5V and +12V current profilesTemperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingAcoustics Air cleanlinessVibration Corrosive environmentX表示该部件(于同类物品程度上)所含的危险和有毒物质中国RoHS MCV标准所定义的门槛值。 China Restriction of Hazardous Substances RoHS DirectiveMechanical specifications Physical dimensionsCheetah NS SAS Product Manual, Rev. B Defect and error management Drive internal defects/errorsDrive error recovery procedures 77.87 SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingCheetah NS SAS Product Manual, Rev. B SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Cheetah NS SAS family drivesCommand name Command code Supported Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Mode Sense data Inquiry dataCheetah NS SAS inquiry data Bytes Data hex Page 2.1 ST3400755SS Mode Sense data Mode PagesSupported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Pin Signal name Signal typeElectrical description SAS pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewAbsolute amplitude Receive eye maskJitter tolerance masks Normalized time in UIJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah NS SAS Product Manual, Rev. B Presales Support Seagate Technology support servicesInternet Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index NumericsPage SAS See also cooling