Seagate ST3400755SS manual Vibration, Acoustics, Air cleanliness, Corrosive environment

Page 35

6.4.4.2Vibration

a.Operating—normal

The drive as installed for normal operation, shall comply with the complete specified performance while subjected to continuous vibration not exceeding

5 - 500 Hz @ 0.5 G (0 to peak, swept sine, 1.0 octive/min) Vibration may be applied in the X, Y, or Z axis.

b.Operating—abnormal

Equipment as installed for normal operation shall not incur physical damage while subjected to periodic vibration not exceeding:

15 minutes of duration at major resonant frequency

Vibration occurring at these levels may degrade operational performance during the abnormal vibration period. Specified operational performance will continue when normal operating vibration levels are resumed. This assumes system recovery routines are available.

Operating abnormal translational random flat profile

5 - 500 Hz

0.75 G (0 to peak)

c.Non-operating

The limits of non-operating vibration shall apply to all conditions of handling and transportation. This includes both isolated drives and integrated drives.

The drive shall not incur physical damage or degraded performance as a result of continuous vibration not

exceeding

 

 

5 - 22 Hz

0.25 G (0 to peak, linear, swept sine, 0.5 octive/min)

22 - 350 Hz

5

G (0 to peak, linear, swept sine, 0.5 octive/min)

350 - 500 Hz

1

G (0 to peak, linear, swept sine, 0.5 octave/min)

Vibration may be applied in the X, Y, or Z axis.

6.4.5Acoustics

Sound power during idle mode shall be 3.6 bels typical when measured to ISO 7779 specification. Sound power while operating shall be 4.0 bels typical when measured to ISO 7779 specification.

There will not be any discrete tones more than 10 dB above the masking noise on typical drives when mea- sured according to Seagate specification 30553-001. There will not be any tones more than 24 dB above the masking noise on any drive.

6.4.6Air cleanliness

The drive is designed to operate in a typical office environment with minimal environmental control.

6.4.7Corrosive environment

Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.

Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro- sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil- ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or

Cheetah NS SAS Product Manual, Rev. B

29

Page 34 Page 36
Image 35
Page 34 Page 36
Contents ST3400755SS Cheetah NS SASPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesTypical ST3400755SS drive +5V and +12V current profiles List of FiguresCheetah NS SAS Product Manual, Rev. B Scope Cheetah NS SAS Product Manual, Rev. B Electromagnetic susceptibility Standards, compliance and reference documentsStandards Electromagnetic compatibilityCompliance Reference documents Cheetah NS SAS Product Manual, Rev. B General description Reliability Standard featuresMedia description PerformanceST3400755SS Factory-installed optionsFormatted capacities Programmable drive capacityCheetah NS SAS Product Manual, Rev. B Seek performance Performance characteristicsInternal drive characteristics Access timeStart/stop time Format command execution time minutesGeneral performance characteristics Caching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Unrecoverable Errors Reliability specificationsError rates Recoverable ErrorsPreventive maintenance Reliability and serviceSeek errors Interface errorsReporting control 4 S.M.A.R.TControlling S.M.A.R.T Performance impactThermal monitor Temperature Log Page 0DhPredictive failures Invoking DST State of the drive prior to testingDST failure definition ImplementationLog page entries Product warrantyShort test Function Code 001b Extended test Function Code 010bProduct repair and return information ShippingCheetah NS SAS Product Manual, Rev. B ST3400755SS DC power requirements Physical/electrical specificationsAC power requirements DC power requirementsCurrent profiles General DC power requirement notesPower sequencing Conducted noise immunityTypical ST3400755SS drive +5V and +12V current profiles Power dissipationEnvironmental limits TemperatureShock Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Package size Packaged/product weight Drop heightCorrosive environment Air cleanlinessVibration AcousticsChina Restriction of Hazardous Substances RoHS Directive X表示该部件（于同类物品程度上）所含的危险和有毒物质中国RoHS MCV标准所定义的门槛值。Physical dimensions Mechanical specificationsCheetah NS SAS Product Manual, Rev. B Drive error recovery procedures Defect and error managementDrive internal defects/errors 77.87 Media Pre-Scan SAS system errorsBackground Media Scan Idle Read After Write Deferred Auto-ReallocationDrive orientation InstallationAir flow CoolingGrounding Drive mountingCheetah NS SAS Product Manual, Rev. B Interface requirements SAS featuresDual port support Command name Command code Supported Scsi commands supportedCommands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Cheetah NS SAS inquiry data Bytes Data hex Mode Sense dataInquiry data Page Mode Pages 2.1 ST3400755SS Mode Sense dataMiscellaneous status Miscellaneous operating features and conditionsMiscellaneous features Supported Feature or conditionSAS physical interface Datum B Connector requirements Physical characteristicsSAS pin descriptions Pin Signal name Signal typeElectrical description Pin descriptionsReady LED Out Signal characteristicsPower SAS transmitters and receiversEye masks Eye masks overview LED drive signalDifferential signals General interface characteristicsNormalized time in UI Receive eye maskJitter tolerance masks Absolute amplitudeFrequency in kHz Peak-toSinusoidal JitterSignal characteristica Units Gbps Transmitter signal characteristicsGbps m, n Deterministic jitterq Receiver signal characteristicsSignal characteristic Units Gbps Maximum allowable jitterImpedance requirements Sheet 1 Impedance specificationsReceiver jitter tolerance Compliant jitter test pattern CjtpatElectrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah NS SAS Product Manual, Rev. B Technical Support Seagate Technology support servicesInternet Presales SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Numerics IndexPage SAS See also cooling
Top Page Image Contents