Seagate ST3400755SS manual General DC power requirement notes, Conducted noise immunity

Page 30

[5]See paragraph 6.2.1, "Conducted noise immunity." Specified voltage tolerance includes ripple, noise, and transient response.

[6]During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track.

General DC power requirement notes.

1.Minimum current loading for each supply voltage is not less than 1.7% of the maximum operating current shown.

2.The +5V and +12V supplies should employ separate ground returns.

3.Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device.

4.Parameters, other than spindle start, are measured after a 10-minute warm up.

5.No terminator power.

6.2.1Conducted noise immunity

Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector.

+5V	=	250 mV pp from 0 to	100 kHz to 20 MHz
+12V	=	800 mV pp from 100	Hz to 8 KHz
		450 mV pp from 8 KHz to 20 KHz
		250 mV pp from 20 KHz to 5 MHz

6.2.2Power sequencing

The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down.

6.2.3Current profiles

The +12V and +5V current profiles are shown below in figure 19.

Note: All times and currents are typical. See Table 2 for maximum current requirements.

24	Cheetah NS SAS Product Manual, Rev. B

Image 30

Contents Cheetah NS SAS ST3400755SSPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Typical ST3400755SS drive +5V and +12V current profilesCheetah NS SAS Product Manual, Rev. B Scope Cheetah NS SAS Product Manual, Rev. B Electromagnetic compatibility Standards, compliance and reference documentsStandards Electromagnetic susceptibilityCompliance Reference documents Cheetah NS SAS Product Manual, Rev. B General description Performance Standard featuresMedia description ReliabilityProgrammable drive capacity Factory-installed optionsFormatted capacities ST3400755SSCheetah NS SAS Product Manual, Rev. B Access time Performance characteristicsInternal drive characteristics Seek performanceFormat command execution time minutes General performance characteristicsStart/stop time Prefetch/multi-segmented cache control Cache operationCaching write data Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlTemperature Log Page 0Dh Predictive failuresThermal monitor Implementation State of the drive prior to testingDST failure definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationCheetah NS SAS Product Manual, Rev. B DC power requirements Physical/electrical specificationsAC power requirements ST3400755SS DC power requirementsConducted noise immunity General DC power requirement notesPower sequencing Current profilesPower dissipation Typical ST3400755SS drive +5V and +12V current profilesTemperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingAcoustics Air cleanlinessVibration Corrosive environmentX表示该部件（于同类物品程度上）所含的危险和有毒物质中国RoHS MCV标准所定义的门槛值。 China Restriction of Hazardous Substances RoHS DirectiveMechanical specifications Physical dimensionsCheetah NS SAS Product Manual, Rev. B Defect and error management Drive internal defects/errorsDrive error recovery procedures 77.87 SAS system errors Background Media ScanMedia Pre-Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingCheetah NS SAS Product Manual, Rev. B SAS features Interface requirementsDual port support Scsi commands supported Commands supported by Cheetah NS SAS family drivesCommand name Command code Supported Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Mode Sense data Inquiry dataCheetah NS SAS inquiry data Bytes Data hex Page 2.1 ST3400755SS Mode Sense data Mode PagesSupported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Pin Signal name Signal typeElectrical description SAS pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewAbsolute amplitude Receive eye maskJitter tolerance masks Normalized time in UIJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Transmitter characteristics Impedance requirements Sheet 2Electrical TxRx connections = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah NS SAS Product Manual, Rev. B Presales Support Seagate Technology support servicesInternet Technical SupportWarranty Service Data Recovery Services Authorized Service CentersData Recovery Services Call Center Toll-free Direct dial Index NumericsPage SAS See also cooling