Seagate ST3400755SS LED drive signal, Differential signals, General interface characteristics

Page 62

The Ready LED Out signal is designed to pull down the cathode of an LED. The anode is attached to the proper +3.3 volt supply through an appropriate current limiting resistor. The LED and the current limiting resis- tor are external to the drive. See Table 12 for the output characteristics of the LED drive signals.

Table 12:	LED drive signal

State		Test condition	Output voltage

LED off, high		0 V ≤ VOH ≤ 3.6 V	-100 µA < IOH < 100 µA

LED on, low		IOL = 15 mA	0 ≤ VOL ≤ 0.225 V

9.5.2Differential signals

The drive SAS differential signals comply with the intra-enclosure (internal connector) requirements of the SAS standard.

Table 13 defines the general interface characteristics.

Table 13: General interface characteristics

Characteristic	Units	1.5 Gbps	3.0 Gbps

Bit rate (nominal)	Mbaud	1,500	3,000

Unit interval (UI)(nominal)	ps	666.6	333.3

Impedance (nominal, differential )	ohm	100	100

Transmitter transients, maximum	V	± 1.2	± 1.2

Receiver transients, maximum	V	± 1.2	± 1.2

9.5.2.1Eye masks

9.5.2.1.1Eye masks overview

The eye masks are graphical representations of the voltage and point. The time values between X1 and (1 - X1) cover all but 10-12of the total jitter population has a range of ± 7 standard deviations.

time limits on the signal at the compliance of the jitter population. The random content

56	Cheetah NS SAS Product Manual, Rev. B

Image 62

Contents Cheetah NS SAS ST3400755SSPage Contents Seagate Technology support services Defect and error managementInstallation Interface requirementsList of Figures Typical ST3400755SS drive +5V and +12V current profilesCheetah NS SAS Product Manual, Rev. B Scope Cheetah NS SAS Product Manual, Rev. B Electromagnetic compatibility Standards, compliance and reference documentsStandards Electromagnetic susceptibilityCompliance Reference documents Cheetah NS SAS Product Manual, Rev. B General description Performance Standard featuresMedia description ReliabilityProgrammable drive capacity Factory-installed optionsFormatted capacities ST3400755SSCheetah NS SAS Product Manual, Rev. B Access time Performance characteristicsInternal drive characteristics Seek performanceStart/stop time Format command execution time minutesGeneral performance characteristics Caching write data Prefetch/multi-segmented cache controlCache operation Prefetch operation Recoverable Errors Reliability specificationsError rates Unrecoverable ErrorsInterface errors Reliability and serviceSeek errors Preventive maintenancePerformance impact 4 S.M.A.R.TControlling S.M.A.R.T Reporting controlThermal monitor Temperature Log Page 0DhPredictive failures Implementation State of the drive prior to testingDST failure definition Invoking DSTExtended test Function Code 010b Product warrantyShort test Function Code 001b Log page entriesShipping Product repair and return informationCheetah NS SAS Product Manual, Rev. B DC power requirements Physical/electrical specificationsAC power requirements ST3400755SS DC power requirementsConducted noise immunity General DC power requirement notesPower sequencing Current profilesPower dissipation Typical ST3400755SS drive +5V and +12V current profilesTemperature Environmental limitsShock and vibration Relative humidityEffective altitude sea level ShockPackage size Packaged/product weight Drop height Recommended mountingAcoustics Air cleanlinessVibration Corrosive environmentX表示该部件（于同类物品程度上）所含的危险和有毒物质中国RoHS MCV标准所定义的门槛值。 China Restriction of Hazardous Substances RoHS DirectiveMechanical specifications Physical dimensionsCheetah NS SAS Product Manual, Rev. B Drive error recovery procedures Defect and error managementDrive internal defects/errors 77.87 Media Pre-Scan SAS system errorsBackground Media Scan Deferred Auto-Reallocation Idle Read After WriteInstallation Drive orientationCooling Air flowDrive mounting GroundingCheetah NS SAS Product Manual, Rev. B SAS features Interface requirementsDual port support Command name Command code Supported Scsi commands supportedCommands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Commands supported by Cheetah NS SAS family drives Cheetah NS SAS inquiry data Bytes Data hex Mode Sense dataInquiry data Page 2.1 ST3400755SS Mode Sense data Mode PagesSupported Feature or condition Miscellaneous operating features and conditionsMiscellaneous features Miscellaneous statusSAS physical interface Datum B Physical characteristics Connector requirementsPin descriptions Pin Signal name Signal typeElectrical description SAS pin descriptionsSAS transmitters and receivers Signal characteristicsPower Ready LED OutGeneral interface characteristics LED drive signalDifferential signals Eye masks Eye masks overviewAbsolute amplitude Receive eye maskJitter tolerance masks Normalized time in UIJitter Peak-toSinusoidal Frequency in kHzTransmitter signal characteristics Signal characteristica Units GbpsMaximum allowable jitter Receiver signal characteristicsSignal characteristic Units Gbps Gbps m, n Deterministic jitterqCompliant jitter test pattern Cjtpat Impedance specificationsReceiver jitter tolerance Impedance requirements Sheet 1Electrical TxRx connections Transmitter characteristicsImpedance requirements Sheet 2 = -5,437dB Shows the zero-length test load Receiver characteristics Cheetah NS SAS Product Manual, Rev. B Presales Support Seagate Technology support servicesInternet Technical SupportData Recovery Services Call Center Toll-free Direct dial Warranty ServiceData Recovery Services Authorized Service Centers Index NumericsPage SAS See also cooling