Barracuda 5400.1 Product Manual, Rev. G | 15 |
2.10.5Shock
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.
2.10.5.1Operating shock
These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.
2.10.5.2Nonoperating shock
The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration.
2.10.6Vibration
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.
2.10.6.1Operating vibration
The following table lists the maximum vibration levels that the drive may experience while meeting the performance standards specified in this docu- ment.
5–21 Hz | 0.02-inch displacement (peak to peak) |
22–350 Hz | 0.50 Gs acceleration (zero to peak) |
2.10.6.2Nonoperating vibration
The following table lists the maximum nonoperating vibration that the drive may experience without incurring physical damage or degradation in perfor- mance when subsequently put into operation.
5–21 Hz | 0.2-inch displacement (peak to peak) |
22–350 Hz | 5.0 Gs acceleration (zero to peak) |
Page
Page
Page
Page
Contents
Barracuda 5400.1 Product Manual, Rev. G
Seagate Technology support services
List of Figures
Barracuda 5400.1 Product Manual, Rev. G
Introduction
Barracuda 5400.1 Product Manual, Rev. G
Specification summary table
Drive specifications
Drive specification ST340015ACE
50,000 Humidity SeaShield
Physical organization
Default logical geometry
LBA mode
ATA
Physical characteristics
Typical seek times msec Read Write
Power specifications
Seek time
Start/stop times
Read/write power and current
Barracuda 5400.1 Product Manual, Rev. G Power consumption
Spinup power
Seek mode
Barracuda 5400.1 Product Manual, Rev. G
Typical 5V startup and operation current profile
Conducted noise
Power-management modes
Active mode
Idle mode
Environmental specifications Ambient temperature
Sleep mode
Idle and Standby timers
Altitude
Temperature gradient
Wet bulb temperature
Humidity Relative humidity
Vibration
Barracuda 5400.1 Product Manual, Rev. G Shock
Operating shock
Nonoperating shock
Model Idle Quiet seek Performance seek
Acoustic mode
Acoustics
Fluid Dynamic Bearing FDB motor acoustics
Performance Reference Test Description Level Standard
Reliability
Korean RRL
Agency certification Safety certification
Electromagnetic compatibility
FCC verification
Barracuda 5400.1 Product Manual, Rev. G
Handling and static discharge precautions
Configuring and mounting the drive
Breather filter hole location
Breather filter hole precautions
Cable select option
Drive as master with a non-ATA-compatible slave
Slave
Ultra ATA/100 cable
Drive mounting
Master
Mounting dimensions-top, side and end view
Barracuda 5400.1 Product Manual, Rev. G
ATA interface
ATA interface signals and connector pins
O pins and supported ATA signals
EC H
Command name Command code in hex ATA-standard commands
Command name Command code in hex
ATA-standard security commands
Identify Device command
0C5AH
Word Description Value
XxxxH
Xx3FH
Description if bit is set to Bit
0CH
Set Features command
F1H Report full capacity available
Code in features Register A.R.T. command
4 S.M.A.R.T. commands
Internet MySeagate
Seagate Technology support services Online Services
40Barracuda 5400.1 Product Manual, Rev. G
Automated Phone Services
USA/Canada/Latin America Support Services
Africa/Middle East Support Services
European Support Services
Asia/Pacific Support Services
Barracuda 5400.1 Product Manual, Rev. G
Index
GMR
Barracuda 5400.1 Product Manual, Rev. G
48Barracuda 5400.1 Product Manual, Rev. G
Page
Seagate Technology LLC