Clarion DMZ637MP owner manual Basic Operations

6. OPERATIONS

Basic Operations

Selecting a DSP menu Adjusting the tone

English

Basic Operations	Note: Be sure to read this chapter referring to the front diagrams of
	chapter “3. CONTROLS” on page 5 (unfold).

The DSP (digital sound processor) function is a function that enables the simulation of sound ef- fects produced by digital signal process in the

Press the [Audio Mode] button and select the item to adjust. Each time you press the [Audio Mode] button, the item changes as following or-

English

CAUTION

Be sure to lower the volume before switch- ing off the unit power or the ignition key. The unit remembers its last volume setting. If you switch the power off with the volume up, when you switch the power back on, the sud- den loud volume may hurt your hearing and damage the unit.

Turning on/off the power

Note:

Adjusting the volume

Turning the [Rotary] knob clockwise increases the volume; turning it counterclockwise de- creases the volume.

∗The volume level is from 0 (minimum) to 33 (maxi- mum).

Switching the display

Press the [Display] button to select the desired display.

Each time you press the [Display] button, the

car, without deteriorating the sound quality.

∗The factory default setting is “STADIUM”.

Each time you press the [D.S.P] button, the tone effect changes in the following order:

“STADIUM” ➜ “HALL” ➜ “CLUB” ➜ “CHURCH” ➜ “L-ROOM” ➜ “DSP OFF” ➜

“STADIUM” ...

• STADIUM	: A sound field with a wide ceiling
	such as a stadium
• HALL	: A sound field such as a large hall

der:

●When “BASS BOOST” is set

“EFFECT” ➜ “B-BOOST” ➜ “BALANCE” ➜ “FADER” ➜ Last function mode.

●When “IMPACT” is set

“EFFECT” ➜ “IMPACT” ➜ “BALANCE” ➜ “FADER” ➜ Last function mode.

●When “EXCITE” is set

“EFFECT” ➜ “EXCITE” ➜ “BALANCE” ➜ “FADER” ➜ Last function mode.

•Be careful about using this unit for a long time without running the engine. If you drain the car’s battery too far, you may not be able to start the engine and this can reduce the service life of the battery.

1.	Press the [Function] button.
2.	The illumination and display on the unit light
	up. The unit automatically remembers its last

display switches in the following order:

Main display

Title display

• CLUB	: A sound field such as a small-
	sized disco hall
• CHURCH	: A sound field with a tall ceiling
	such as a cathedral
• L-ROOM	: A sound field such as a listening
	room
• DSP OFF	: no sound effect

●When “USER CUSTOM” is set

“EFFECT” ➜ “BASS” ➜ “TREBLE” ➜ “BAL- ANCE” ➜ “FADER” ➜ Last function mode.

●When “Z-EHCR+ OFF” is set

“EFFECT” ➜ “BALANCE” ➜ “FADER” ➜

Last function mode.

operation mode and will automatically switch

to display that mode.

3. Press and hold the [Function] button for 1

second or longer to turn off the power for the

unit.

Note:

•System check

The first time this unit is turned on after the wire connections are completed, it must be checked what equipment is connected. When the power is turned on, “SYSTEM CHECK” and “Push POWER” appear in the display alternately, so press the [Function] button. The system check starts within the unit. When the system check is complete, press the [Function] button again.

Selecting a mode

1.Press the [Function] button to change the operation mode.

2.Each time you press the [Function] button, the operation mode changes in the following order:

Radio mode ➜ CD/MP3 mode ➜ MD mode

➜CD changer mode ➜ MD changer mode

➜DVD changer mode ➜ TV mode ➜ AUX mode ➜ Radio mode...

∗External equipment not connected with CeNET is not displayed.

Clock display

Main display

∗Once selected, the preferred display becomes the display default. When a function adjust- ment such as volume is made, the screen will momentarily switch to that function’s display, then revert back to the preferred display sev- eral seconds after the adjustment.

∗When you have entered a title in a CD, it ap- pears in the main display. If you have not en- tered a title, “NO TITLE” appears in the title display instead. For information on how to en- ter a title, refer to the subsection “Entering titles” in section “Operations Common to Each Mode”.

Setting the Z-Enhancer Plus

This unit are provided with 3 types of sound tone ef- fects stored in memory. Select the one you prefer.

∗The factory default setting is “Z-EHCR+ OFF”.

Each time you press the [Z-Enhancer+] button, the tone effect changes in the following order:

“Z-EHCR+ OFF” ➜ “BASS BOOST” ➜ “IM- PACT” ➜ “EXCITE” ➜ “USER CUSTOM” ➜

“Z-EHCR+ OFF” ...

• BASS BOOST	: bass emphasized
• IMPACT	: bass and treble empha-
	sized
• EXCITE	: bass and treble empha-
	sized mid de-emphasized
• USER CUSTOM	: user custom
• Z-EHCR+ OFF	: no sound effect

Adjusting the Effect

Effect means a reflecting sound that rebounds against the walls, etc. The volume of the re- flected sound can be changed on this unit (When DSP function is “on”).

1.Press the [Audio Mode] button and select the Effect to adjust.

2.Turning the [Rotary] knob for adjustment.

∗ Adjustment range 0% to 70%

Adjusting the Z-Enhancer Plus

1.Press the [Z-Enhancer+] button and select the Z-Enhancer Plus mode to adjust.

2.Press the [Audio Mode] button and select the Z-Enhancer Plus mode to adjust.

3.Turning the [Rotary] knob for adjustment.

●When “B-BOOST 0” selected, you can ad- just the bass in the range of –3 to 3.

●When “IMPACT 0” selected, you can adjust the bass and treble in the range of –3 to 3.

●When “EXCITE 0” selected, you can adjust the bass and treble in the range of –3 to 3.

Adjusting the bass (Gain,

Frequency, Q-curve)

This adjustment can be performed when the Z- Enhancer Plus is set to “USER CUSTOM”.

1.Press the [Audio Mode] button and select “BASS”.

2.Turning the [Rotary] knob clockwise empha- sizes the bass; turning it counterclockwise at- tenuates the bass.

∗The factory default setting is “BASSÅG 0Δ. (Adjustment range: –6 to +6)

3.Press the [A] or [D] button to select “BASSÅFREQΔ.

Turninng the [Rotary] knob clockwise or counterclockwise to select the frequency.

10 DMZ637MP DMZ637MP 11