Tyco Electronics 1529L manual Optimizing the LCD Display, Installing the Peripheral Device Drivers

Page 30

Optimizing the LCD Display

To ensure the LCD display works well with your computer, configure the display mode of your graphic card to make it less than or equal to 1024 x 768 resolution, and make sure the timing of the display mode is compatible with the LCD display. Refer to Appen- dix A for more information about resolution. Compatible video modes for your touchmonitor are listed in Appendix C.

Installing the Peripheral Device Drivers

Finger Print Reader

NOTE: This driver is for MS Windows 9x through XP.

1On the TouchTools CD, browse to Touch Monitor Peripherals\Finger

Print Readers\Fingerprint Reader 229L 1529L\Driver Install\Drivers.

2Double-click setup.exe

Follow the Install Shield Wizard procedure to complete the installation. For a detailed software development kit, browse to Touch Monitor

Peripherals\Finger Print Readers\Fingerprint Reader 229L 1529L\Driver Install\Drivers and open the following files:

FDxSDKforWindows1 .20.zip

SecuBSPSDK for Windows2 .10.zip

You will enter one of the following serial numbers depending on your operating system:

FDx SDK for Windows: 31-100s101-3586383

FDx SDK for Windows CE: 32-100s101-9713291

SecuBSP SDK for Windows: 41-100s101-7685871

SecuBSP SDK for Windows CE: 42-100s101-1155462

SecuBSP SDK: 51-100s101-5963137

Once the driver setup is complete, the demo program can be run from Touch Monitor

Peripherals\Finger Print Readers\Fingerprint Reader 229L 1529L\Demo\ BSPDemo.exe

2-24 Elo Touchmonitor User Guide

Image 30
Contents Touchmonitor User Guide Elo Touchmonitor User Guide 008603E Elo TouchSystemsCopyright 2008 Tyco Electronics. All Rights Reserved Table of Contents Appendix B Page Introduction Product DescriptionDetailed LCD Display Performance Requirements Inch TFT LCD Display PanelCustomer Display Serial Version Optional ParametersCredit Card Reader Barcode ScannerExternal Power Supply Six Port USB HubElo Touchmonitor User Guide Installation and Setup Unpacking Your TouchmonitorProduct Overview Side View Base Bottom View KensingtonTM Lock USB Interface Connection Remove the Cable CoverHole in the second as shown in the picture above Page Elo Touchmonitor User Guide Page Elo Touchmonitor User Guide USB / Serial Interface Connection Hole in the second as shown in the picture above Page Elo Touchmonitor User Guide Page Elo Touchmonitor User Guide Replace the Cable Cover Installing the Peripheral Device Drivers Optimizing the LCD DisplayFinger Print Reader Magnetic Stripe Reader Testing the USB MSR Keyboard EmulationTesting the USB-HID Class MSR Convert MSR from HID to keyboard EmulationConvert MSR from keyboard emulation to HID Rear Facing Customer DisplayInsert your Elo TouchTools CD Elo Touchmonitor User Guide Installing the Touch Driver Software MS DOSClick Start Run About Touchmonitor Adjustments OperationLCD Function Key OSD Lock/Unlock Controls and AdjustmentPower Lock/Unlock OSD Menu FunctionsColor Temperature PhaseAuto Adjust Recall DefaultsPower-Save No Input Power LED Display & Power Saving General Power Saving ModeDisplay Angle Take care not to touch the screen Controls and Adjustment Gain of R, G, and B signal is adjusted Restore all original factory defaults Elo Touchmonitor User Guide Troubleshooting Solutions to Common ProblemsElo Touchmonitor User Guide Native Resolution Input Video 15.0 LCDElo Touchmonitor User Guide Touchmonitor Safety Care and Handling of Your Touchmonitor Waste Electrical and Electronic EquipmentWEEE DirectiveTechnical Specifications Display ModesTouchmonitor Specifications Display ModeAccuTouch Touchscreen Specifications Mechanical ConstructionIntelliTouch Touchscreen Specifications Expected Life PerformanceInfrared Touchscreen Specifications Acoustic Pulse Recognition Specification ElectricalPage Elo Touchmonitor User Guide Electrical Safety Information Regulatory InformationElo Touchmonitor User Guide Vorsicht Elo Touchmonitor User Guide Warranty Elo Touchmonitor User Guide Index D E X Check out Elo’s Web site