Tyan Computer N3600T, S2937 warranty Congratulations, Hardware Specifications

Page 5

Chapter 1: Instruction

1.00 – Congratulations

You are now the owner of the ideal solution for rackmount servers. Tyan S2937 supports Dual AMD Opteron 2000 series processors, up to 64G Registered/ECC memories, 2 Gigabit Ethernet ports, one IDE connector, 6 Serial ATA-II (SATA) connectors, 8 SAS connectors and 2 USB ports. S2937 offers exceptional performance for your server platform needs.

Remember to visit TYAN’s Website at http://www.TYAN.com. There you can find information on all of TYAN’s products with FAQs, online manuals and BIOS upgrades.

1.01 – Hardware Specifications

Processors

Integrated Serial ATA II Controller

- Dual 1207-pin sockets

- Supports (6) SATA-II ports

- Supports up to 2 x AMD Opteron

- Supports up to 3.0Gb/s

Rev.F 2000 series Dual-core / Quad-

- Supports RAID 0, 1, 0+1, 5

core processors.

 

- Up to 1.0GHz Hyper-Transport link

System Management

support

- (9) 4-pin fan headers

- AMD Dual Dynamic Power support

- CPU temperature & voltage monitor

Chipset

support

- Watchdog timer support

- nVidia NFP3600 (MCP55)

Integrated SAS Controller

- Winbond 83627HG Super I/O chip

- Analog Devices ADT7476 Hardware

- LSI® 1068E SAS controller with PCI-

Monitoring IC

E x4 interface

Memory

- Supports (8) SAS/SATA ports

- RAID 0, 1 and 1E support

- Dual-channel memory bus

Integrated LAN Controller

- (16) 240-pin DDR2 DIMM sockets (8

per CPU)

- Intel “Ophir” (82571EB) Gigabit

- Supports registered, ECC DIMMs

Ethernet Controller

- 64GB maximum of DDR2 667 / 533 /

- (2) 10/100/1000 LAN ports

400 memory

Server Management

Expansion Slots

- OPMA card support M3

- (2) PCI-E x16 slots (w/ x8 signal)

- TYAN M3295-2

- (1) PCI-E x16 slot (w/ x4 signal)

 

- (1) OPMA connector support M3

 

OPMA card

 

5

http://www.TYAN.com

Image 5
Contents Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Congratulations Hardware SpecificationsIntegrated 2D/3D PCI Graphics PowerIntegrated I/O Interfaces Back Panel I/O PortsOS Operating Systems Support Software SpecificationsHow to install our products right… the first time Board InstallationBoard Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 Normal Default Clear SAS Disable Jumper JP1Opma card supporting select header JP2 Clear Cmos JP3JP10 JP9 JP11 Front Panel Header J26LAN1/LAN2 Enable/ Disable Jumper JP9, JP10 Ipmb Connector IpmbTPM Enable/ Disable Jumper JP11 Signal PinOnboard VGA Enable/ Disable Jumper JP8 System FAN Headers SYS FAN1/2/3/4/5/6/7 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2J116 J118 J113 J111 J15 Tyan Front Panel 2 for Barebones J15LCD Module Header for Barebones J113 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Type a CAM Lever Type Installation Heatsink Installation ProceduresType B Screw Retention Type Heatsink Finishing Installing the HeatsinkAttaching Drive Cables Sata Drivers Floppy Drives Drive does not power onPCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signal Installing Add-In CardsDescription Left LED Right LED Connecting External Devices24-pin Pin Installing the Power SupplyApplying power to the board Finishing Up Starting Setup Bios About the BiosGetting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Advanced Installed O/SReset Configuration Data HT-LDT Frequency Hammer ConfigurationNode Interleave Dram Bank InterleaveECC Options Sub-Menu ECC Mode Multiprocessor SpecificationAuto DQS Training Processor Assisted VirtualizationsECC Error Log ECC Error CheckingECC Multibit Error Detection ChipKillIommu Size Memory Controller Options Sub-Menu Mem Hole RemapMemory Clock Memory Config Options Sub-Menu Mem Clock ModeInterrupt Mode USB Bios Legacy SupportIntegrated Devices USB ControlSata port 0/1/2/3/4/5 Raid NV RAID Configuration Sub-MenuLocal Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode Primary Master / Slave Sub-Menu LBA Mode ControlType Multi-Sector TransfersBit I/O Transfer ModeUltra DMA Mode Floppy check Floppy ConfigurationLegacy Diskette a Selects floppy type Serial Port a 5 I/O Device ConfigurationBase I/O Address InterruptParallel Port ModeDMA Channel Floppy Disk ControllerHardware Monitor / Ipmi AutoFan ModeCOM Port Address Console RedirectionBaud Rate Console TypeEvent Log Capacity DMI Event LoggingEvent Log Validity View DMI Event LogSecurity Boot EndLess PXE Loop Boot Device Priority Boot Priority OrderExcluded from boot order Enable Acpi PowerPower Button Off After Power FailureLDT Spread Spectrum Spread Spectrum Tgio Spread SpectrumSata Spread Spectrum CPU PLL Spread SpectrumAMD PowerNow Acpi Table High Precision Event timerAcpimcfg Table Acpi Srat TableExit Page Memory, Video, CPU DiagnosticsFlash Utility Code Beeps / Description Phoenix Bios Post CodePEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support