Tyan Computer S2937, N3600T Board Installation, How to install our products right… the first time

Page 8

Chapter 2: Board Installation

You are now ready to install your motherboard. The mounting-hole pattern of the S2937 matches the E-ATX specifications. Before continuing with installation, confirm that your chassis supports an E-ATX motherboard.

How to install our products right… the first time!

The first thing you should do is to read this user’s manual. It contains important information which will make configuration and setup much easier. Here are some precautions you should take when installing your motherboard:

(1)Ground yourself properly before removing your motherboard from the antistatic bag. Unplug the power from your computer power supply and then touch a safely grounded object to release static charge (i.e. power supply case). For the safest conditions, TYAN recommends wearing a static safety wrist strap.

(2)Hold the motherboard by its edges and do not touch the bottom of the board, or flex the board in any way.

(3)Avoid touching the motherboard components, IC chips, connectors, memory modules, and leads.

(4)Place the motherboard on a grounded antistatic surface or on the antistatic bag that the board was shipped in.

(5)Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as well as installing the processor, memory, disk drives and cables.

NOTE

DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED.

8

http://www.TYAN.com

Image 8

Contents Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Hardware Specifications CongratulationsPower Integrated 2D/3D PCI GraphicsIntegrated I/O Interfaces Back Panel I/O PortsSoftware Specifications OS Operating Systems SupportBoard Installation How to install our products right… the first timeBoard Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 SAS Disable Jumper JP1 Normal Default ClearOpma card supporting select header JP2 Clear Cmos JP3Front Panel Header J26 JP10 JP9 JP11Ipmb Connector Ipmb LAN1/LAN2 Enable/ Disable Jumper JP9, JP10TPM Enable/ Disable Jumper JP11 Signal PinOnboard VGA Enable/ Disable Jumper JP8 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2 System FAN Headers SYS FAN1/2/3/4/5/6/7J116 J118 J113 J111 J15 Tyan Front Panel 2 for Barebones J15LCD Module Header for Barebones J113 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Heatsink Installation Procedures Type a CAM Lever Type InstallationFinishing Installing the Heatsink Type B Screw Retention Type HeatsinkAttaching Drive Cables Sata Drivers Drive does not power on Floppy DrivesInstalling Add-In Cards PCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signalConnecting External Devices Description Left LED Right LED24-pin Pin Installing the Power SupplyApplying power to the board Finishing Up Bios About the Bios Starting SetupGetting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Advanced Installed O/SReset Configuration Data Hammer Configuration HT-LDT FrequencyNode Interleave Dram Bank InterleaveMultiprocessor Specification ECC Options Sub-Menu ECC ModeAuto DQS Training Processor Assisted VirtualizationsECC Error Checking ECC Error LogECC Multibit Error Detection ChipKillMemory Controller Options Sub-Menu Mem Hole Remap Iommu SizeMemory Config Options Sub-Menu Mem Clock Mode Memory ClockUSB Bios Legacy Support Interrupt ModeIntegrated Devices USB ControlNV RAID Configuration Sub-Menu Sata port 0/1/2/3/4/5 RaidLocal Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode LBA Mode Control Primary Master / Slave Sub-MenuType Multi-Sector TransfersBit I/O Transfer ModeUltra DMA Mode Floppy check Floppy ConfigurationLegacy Diskette a Selects floppy type 5 I/O Device Configuration Serial Port aBase I/O Address InterruptMode Parallel PortDMA Channel Floppy Disk ControllerAutoFan Mode Hardware Monitor / IpmiConsole Redirection COM Port AddressBaud Rate Console TypeDMI Event Logging Event Log CapacityEvent Log Validity View DMI Event LogSecurity Boot EndLess PXE Loop Boot Device Priority Boot Priority OrderExcluded from boot order Power Enable AcpiPower Button Off After Power FailureSpread Spectrum Tgio Spread Spectrum LDT Spread SpectrumSata Spread Spectrum CPU PLL Spread SpectrumAcpi Table High Precision Event timer AMD PowerNowAcpimcfg Table Acpi Srat TableExit Page Memory, Video, CPU DiagnosticsFlash Utility Phoenix Bios Post Code Code Beeps / DescriptionPEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support