Tyan Computer S2937, N3600T warranty Exit

Page 68

3.08 Exit

These settings set the exit options on your system.

Exit Saving Changes

This exits BIOS setup after saving the changes made.

Exit Discarding Changes

This exits BIOS setup after discarding the changes made.

Load Setup Defaults

This loads the factory default values.

Discard Changes

This discards all changes made without exiting BIOS setup.

Save Changes

This saves all changes made without exiting BIOS setup.

68

http://www.tyan.com

Image 68
Contents Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Hardware Specifications CongratulationsPower Integrated 2D/3D PCI GraphicsIntegrated I/O Interfaces Back Panel I/O PortsSoftware Specifications OS Operating Systems SupportBoard Installation How to install our products right… the first timeBoard Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 SAS Disable Jumper JP1 Normal Default ClearOpma card supporting select header JP2 Clear Cmos JP3Front Panel Header J26 JP10 JP9 JP11Ipmb Connector Ipmb LAN1/LAN2 Enable/ Disable Jumper JP9, JP10TPM Enable/ Disable Jumper JP11 Signal PinOnboard VGA Enable/ Disable Jumper JP8 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2 System FAN Headers SYS FAN1/2/3/4/5/6/7J116 J118 J113 J111 J15 Tyan Front Panel 2 for Barebones J15LCD Module Header for Barebones J113 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Heatsink Installation Procedures Type a CAM Lever Type InstallationFinishing Installing the Heatsink Type B Screw Retention Type HeatsinkAttaching Drive Cables Sata Drivers Drive does not power on Floppy DrivesInstalling Add-In Cards PCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signalConnecting External Devices Description Left LED Right LED24-pin Pin Installing the Power SupplyApplying power to the board Finishing Up Bios About the Bios Starting SetupGetting Help Case of ProblemsSetup Variations Main Bios Setup Main System Time / System Date Advanced Installed O/SReset Configuration Data Hammer Configuration HT-LDT FrequencyNode Interleave Dram Bank InterleaveMultiprocessor Specification ECC Options Sub-Menu ECC ModeAuto DQS Training Processor Assisted VirtualizationsECC Error Checking ECC Error LogECC Multibit Error Detection ChipKillMemory Controller Options Sub-Menu Mem Hole Remap Iommu SizeMemory Config Options Sub-Menu Mem Clock Mode Memory ClockUSB Bios Legacy Support Interrupt ModeIntegrated Devices USB ControlNV RAID Configuration Sub-Menu Sata port 0/1/2/3/4/5 RaidLocal Bus IDE Adapter IDE ConfigurationLarge Disk Access Mode LBA Mode Control Primary Master / Slave Sub-MenuType Multi-Sector TransfersBit I/O Transfer ModeUltra DMA Mode Floppy check Floppy ConfigurationLegacy Diskette a Selects floppy type 5 I/O Device Configuration Serial Port aBase I/O Address InterruptMode Parallel PortDMA Channel Floppy Disk ControllerAutoFan Mode Hardware Monitor / IpmiConsole Redirection COM Port AddressBaud Rate Console TypeDMI Event Logging Event Log CapacityEvent Log Validity View DMI Event LogSecurity Boot EndLess PXE Loop Boot Device Priority Boot Priority OrderExcluded from boot order Power Enable AcpiPower Button Off After Power FailureSpread Spectrum Tgio Spread Spectrum LDT Spread SpectrumSata Spread Spectrum CPU PLL Spread SpectrumAcpi Table High Precision Event timer AMD PowerNowAcpimcfg Table Acpi Srat TableExit Page Memory, Video, CPU DiagnosticsFlash Utility Phoenix Bios Post Code Code Beeps / DescriptionPEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support