Tyan Computer S2937, N3600T warranty

Page 82

service by calling the manufacturer for a Return Merchandise Authorization (RMA) number. The RMA number should be prominently displayed on the outside of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you.

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC

FCC Part 15: This device complies with part 15 of the FCC

Rules

Operation is subject to the following conditions:

This device may not cause harmful interference, and

This device must accept any interference received including interference that may cause undesired operation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Plug the equipment into an outlet on a circuit different from that of the receiver. Consult the dealer on an experienced radio/television technician for help.

Notice for Canada

This apparatus complies with the Class B limits for radio interference as specified in the Canadian Department of Communications Radio Interference Regulations. (Cet appareil est conforme aux norms de Classe B d’interference radio tel que specifie par le Ministere Canadien des Communications dans les reglements d’ineteference radio.)

Notice for Europe (CE Mark)

This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC (EMC).

CAUTION: Lithium battery included with this board. Do not puncture, mutilate, or dispose of battery in fire. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by manufacturer. Dispose of used battery according to manufacturer instructions and in accordance with your local regulations.

Document #: D1952 - 100

82

http://www.tyan.com

Image 82
Contents Thunder n3600T Table of Contents Appendix Glossary …………………………Page Technical Support Check the box contents Hardware Specifications CongratulationsIntegrated I/O Interfaces PowerIntegrated 2D/3D PCI Graphics Back Panel I/O PortsSoftware Specifications OS Operating Systems SupportBoard Installation How to install our products right… the first timeBoard Image Block Diagram Board Parts, Jumpers and Connectors Jumper settings JP2 JP3 JP1 Opma card supporting select header JP2 SAS Disable Jumper JP1Normal Default Clear Clear Cmos JP3Front Panel Header J26 JP10 JP9 JP11TPM Enable/ Disable Jumper JP11 Ipmb Connector IpmbLAN1/LAN2 Enable/ Disable Jumper JP9, JP10 Signal PinOnboard VGA Enable/ Disable Jumper JP8 CPU1 & CPU2 FAN Header CPU FAN1, CPU FAN2 System FAN Headers SYS FAN1/2/3/4/5/6/7LCD Module Header for Barebones J113 Tyan Front Panel 2 for Barebones J15J116 J118 J113 J111 J15 Fan Connector for Barebones J111 Tips on Installing Motherboard in Chassis Page Installing the Processors Back plate Assembly Page Processor Installation Page Installing the Memory Memory Installation Procedure Thermal Interface Material Heatsink Installation Procedures Type a CAM Lever Type InstallationFinishing Installing the Heatsink Type B Screw Retention Type HeatsinkAttaching Drive Cables Sata Drivers Drive does not power on Floppy DrivesInstalling Add-In Cards PCI-E x 16 slot w/ x 4 signal PCI-E x 16 slot w/ x 8 signalConnecting External Devices Description Left LED Right LEDApplying power to the board Installing the Power Supply24-pin Pin Finishing Up Bios About the Bios Starting SetupSetup Variations Case of ProblemsGetting Help Main Bios Setup Main System Time / System Date Reset Configuration Data Installed O/SAdvanced Node Interleave Hammer ConfigurationHT-LDT Frequency Dram Bank InterleaveAuto DQS Training Multiprocessor SpecificationECC Options Sub-Menu ECC Mode Processor Assisted VirtualizationsECC Multibit Error Detection ECC Error CheckingECC Error Log ChipKillMemory Controller Options Sub-Menu Mem Hole Remap Iommu SizeMemory Config Options Sub-Menu Mem Clock Mode Memory ClockIntegrated Devices USB Bios Legacy SupportInterrupt Mode USB ControlNV RAID Configuration Sub-Menu Sata port 0/1/2/3/4/5 RaidLarge Disk Access Mode IDE ConfigurationLocal Bus IDE Adapter Type LBA Mode ControlPrimary Master / Slave Sub-Menu Multi-Sector TransfersUltra DMA Mode Transfer ModeBit I/O Legacy Diskette a Selects floppy type Floppy ConfigurationFloppy check Base I/O Address 5 I/O Device ConfigurationSerial Port a InterruptDMA Channel ModeParallel Port Floppy Disk ControllerAutoFan Mode Hardware Monitor / IpmiBaud Rate Console RedirectionCOM Port Address Console TypeEvent Log Validity DMI Event LoggingEvent Log Capacity View DMI Event LogSecurity Boot Excluded from boot order Boot Device Priority Boot Priority OrderEndLess PXE Loop Power Button Off PowerEnable Acpi After Power FailureSata Spread Spectrum Spread Spectrum Tgio Spread SpectrumLDT Spread Spectrum CPU PLL Spread SpectrumAcpimcfg Table Acpi Table High Precision Event timerAMD PowerNow Acpi Srat TableExit Page Flash Utility DiagnosticsMemory, Video, CPU Phoenix Bios Post Code Code Beeps / DescriptionPEM Page Appendix I How to Make a Driver Diskette NVidia ====Choose Chipset Model==== NVidia Nvraid Glossary Page Page Page Page Technical Support