Tyan Computer TYAN S1471 user manual 9DRAM Installation

Page 14

3.9DRAM Installation

The S1471 uses a 64-bit data path from memory to CPU and can accommodate up to 128 MB of RAM. The mainboard supports Fast Page Mode, and EDO (Extended Data Out) 72 pin SIMMs. SDRAM(Synchronous) are also supported in the DIMM slots. DIMM's must be of the unbuffered variety. All installed memory will be automati- cally detected so there is no need to set jumpers.

wSIMM modules must be installed in pairs.

wEach pair of SIMMs must be of the same size and type. wThe mainboard supports 1, 2, 4 and 8MBx32 SIMMs.

wSIMM bank 0 and 1 can use either double or single sided SIMMs.

wTwo SIMMs or One unbuffered DIMM must be installed for the system to POST.

wSDRAM DIMMs can be installed one at a time.

wThe mainboard supports 1, 2 and 4Mx 64 DIMM modules.

wSIMM bank 0 and DIMM bank 0 cannot be used at the same time. SIMM bank 1 and DIMM bank 1 cannot be used at the same time. You can use SIMM bank 0 with DIMM bank 1.

You can use SIMM bank 1 with DIMM bank 0.

wThe following table shows some of the available memory configurations.

DRAM Bank

DRAM

SDRAM Bank

SDRAM Bank

Total

0

Bank 1

0

1

 

 

 

 

 

 

4MB x2

none

none

none

8MB

 

 

 

 

 

none

none

8MB x1

none

8MB

 

 

 

 

 

none

none

16MB x1

none

16MB

 

 

 

 

 

8MB x2

none

none

none

16MB

 

 

 

 

 

4MB x2

4MB x2

none

none

16MB

 

 

 

 

 

8MB x2

8MB x2

none

none

32MB

 

 

 

 

 

16MB x2

none

none

none

32MB

 

 

 

 

 

none

none

16MB x1

none

32MB

 

 

 

 

 

32MB x2

none

none

none

64MB

 

 

 

 

 

16MB x2

16MB x2

none

none

64MB

 

 

 

 

 

16MB x2

none

none

32MB x1

64MB

 

 

 

 

 

none

none

32MB x1

32MB x1

64MB

 

 

 

 

 

32MB x2

16MB x2

none

none

96MB

 

 

 

 

 

32MB x2

none

none

32MB x1

96MB

 

 

 

 

 

32MB x2

32MB x2

none

none

128MB

 

 

 

 

 

S1471-001-01 http://www.tyan.com

14

 

 

 

 

 

 

 

 

 

Image 14
Contents Tyan S1471 Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1471 Board Layout RTCCPU Speed Settings for Cyrix/SGS/IBM 6x86/M1 J15 J40 J39 CPU Voltage Regulator SettingsDefault CPU Multiplier J40 and J39 Volts J11 DefaultOff Memory Voltage DIMMs Default is Volts Host Bus Setting J15Cmos Resest/Password Reset J45Default off Reset Connector J41 Turbo LED Connector J48 Flash Eprom J50Keylock Connector J47 Infra Red Interface Con9 and Con10 Port Setting J13 and J14Speaker Connector J42 Turbo Switch J49 VCCTurbo LED Connector Installation Speaker Connector InstallationTurbo Switch Hardware Reset Switch Connector Installation Refer to for Flash Eprom upgrade procedures9DRAM Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryConnecting the Power Supply GND GND VCCPage Press F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Entering SetupTo Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEY Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuChipset features setup Standard Cmos setupBios features setup Power Management setupTime Standard Cmos Setup MenuDate Primary/Secondary Drive type Drive a type/Drive B typeHalt On VideoEGA/VGA MemoryExpanded Memory Other MemoryVirus warning Boot SequenceSwap Floppy Drive Default value is Disabled CPU Internal Cache/External CacheBoot Up Floppy Seek Boot Up NumLock Status Default value is OnChipset Features Screen Chipset Features SetupVideo Bios Shadow Security OptionWVideo Off Method Power ManagementWPM Control by APM WPower Down Activities Doze ModeWStandby Mode PCI Slot Configuration Legacy ISA Resources Controlled ByWIRQ n assigned to PCI/ISA PnPIntegrated Peripherals Load Setup Defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterDMA Channels Timer MAPSystem Resource NMI