Tyan Computer TYAN S1471 user manual Hardware Specifications/Features

Page 4

1.2 Hardware Specifications/Features

wCPU

Intel Pentium 75 MHz thru 200 MHz (Socket 7)

 

Intel Pentium P55C

 

Cyrix/IBM/SGS M1/6x86 P120, P150 & P166

wSpeed

50/60/66 MHz system bus

 

25/30/33 MHz PCI bus

 

7.5/8.33 MHz ISA bus speed

wDRAM

2 banks of 72 pin SIMM and 2 DIMM Banks

 

Supports 5V or 3.3V memory

 

Supports EDO(Exended Data Out) DRAMs

 

Supports SDRAM(Synchronous DRAM)

 

Supports Fast Page Mode DRAMs

 

Supports 8MB to 128MB of DRAMs

wL2 Cache

16KB cache memory included in Pentium

 

256/512KB on board 2nd level cache memory

 

Supports synchronous pipeline-burst

wEIDE Controller

Primary and secondary PCI EIDE channels on

 

board for support of up to four EIDE Mode 0

 

through Mode 4 drives.

 

Supports DMA(Bus Master) mode 1 and 2.

 

( Bus Master driver on web at www.tyan.com)

wEnhanced I/O

Multi-mode bi-directional parallel port that

 

supports standard, EPP and ECP modes.

 

Supports 16550 compatible Uarts for on-board

 

high speed serial ports.

 

Support for an IrDA compliant Infra Red inter-

 

face.

 

On-board floppy controller

 

Support for On-board Universal Serial Port

wI/O Bus Slots

5 Master/Slave PCI-Bus

 

4 ISA Bus one ISA and one PCI slot is shared

 

for a total of 8 slots.

S1471-001-01 http://www.tyan.com

4

 

 

 

 

 

 

 

 

 

Image 4
Contents Tyan S1471 Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1471 Board Layout RTCCPU Speed Settings for Cyrix/SGS/IBM 6x86/M1 J15 J40 J39 CPU Voltage Regulator SettingsVolts J11 Default Off Memory Voltage DIMMs Default is VoltsDefault CPU Multiplier J40 and J39 Host Bus Setting J15Keylock Connector J47 Reset Connector J41 Turbo LED Connector J48 Flash Eprom J50Cmos Resest/Password Reset J45Default off Port Setting J13 and J14 Speaker Connector J42 Turbo Switch J49Infra Red Interface Con9 and Con10 VCCTurbo Switch Speaker Connector InstallationTurbo LED Connector Installation Hardware Reset Switch Connector Installation Refer to for Flash Eprom upgrade procedures9DRAM Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryConnecting the Power Supply GND GND VCCPage To Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEY Entering SetupPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuStandard Cmos setup Bios features setupChipset features setup Power Management setupDate Standard Cmos Setup MenuTime Primary/Secondary Drive type Drive a type/Drive B typeVideo EGA/VGAHalt On MemoryExpanded Memory Other MemoryBoot Sequence Swap Floppy Drive Default value is DisabledVirus warning CPU Internal Cache/External CacheBoot Up Floppy Seek Boot Up NumLock Status Default value is OnChipset Features Setup Video Bios ShadowChipset Features Screen Security OptionWPM Control by APM Power ManagementWVideo Off Method WStandby Mode Doze ModeWPower Down Activities PCI Slot Configuration Resources Controlled By WIRQ n assigned toLegacy ISA PCI/ISA PnPIntegrated Peripherals Load Setup Defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterTimer MAP System ResourceDMA Channels NMI