Tyan Computer TYAN S1471 user manual Table Of Contents

Page 2

Table Of Contents

 

1. Introduction

3

1.1 Overview

3

1.2 Hardware Specifications

4

1.3 Software Specifications

5

1.4 Environment

5

2. Board Installation

6

2.1 Unpacking

6

2.2 Installation

6

3. S1471 On Board Resource Settings

7

3.1 S1471 Board Layout & Jumper Locations

7

3.2 Quick Reference for Jumpers

8

3.3 CMOS RTC

12

3.4 Speaker Connector

12

3.5 Turbo Switch

12

3.6 Turbo LED Connect

12

3.7 Reset Connector

13

3.8 Flash EPROM Jumpers

13

3.9 DRAM Installation

14

3.10 CPU Installation

15

3.11 Cache Upgrade

16

3.12 Peripheral Device Installation

16

3.13 Connecting The Power Supply

17

4. BIOS Configuration

19

4.1 Entering Setup

19

4.2 Control Keys

20

4.3 Getting Help

21

4.4 The Main Menu

21

4.5 Standard CMOS Setup Menu

23

4.6 BIOS Features Setup

26

4.7 Chipset Features Setup

29

4.7.1 Power Management Setup

30

4.8 PCI Slot Configuration

32

4.9 Integrated Peripherals

34

4.10 Load Setup Defaults

35

4.11 Password Setting

35

4.12 IDE HDD Auto Detection

37

4.13 Save & Exit Setup

37

5. Flash Writer Utility

38

5.1 The Flash Memory Writer Utility Screen

40

6. System Resources

41

6.1 Timer & DMA Channel Map

41

S1471-001-01 http://www.tyan.com

2

 

 

 

 

 

 

 

 

 

Image 2
Contents Tyan S1471 Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1471 Board Layout RTCCPU Speed Settings for Cyrix/SGS/IBM 6x86/M1 J15 J40 J39 CPU Voltage Regulator SettingsDefault CPU Multiplier J40 and J39 Volts J11 DefaultOff Memory Voltage DIMMs Default is Volts Host Bus Setting J15Cmos Resest/Password Reset J45Default off Reset Connector J41 Turbo LED Connector J48 Flash Eprom J50Keylock Connector J47 Infra Red Interface Con9 and Con10 Port Setting J13 and J14Speaker Connector J42 Turbo Switch J49 VCCTurbo LED Connector Installation Speaker Connector InstallationTurbo Switch Hardware Reset Switch Connector Installation Refer to for Flash Eprom upgrade procedures9DRAM Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryConnecting the Power Supply GND GND VCCPage Press F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Entering SetupTo Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEY Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuChipset features setup Standard Cmos setupBios features setup Power Management setupTime Standard Cmos Setup MenuDate Primary/Secondary Drive type Drive a type/Drive B typeHalt On VideoEGA/VGA MemoryExpanded Memory Other MemoryVirus warning Boot SequenceSwap Floppy Drive Default value is Disabled CPU Internal Cache/External CacheBoot Up Floppy Seek Boot Up NumLock Status Default value is OnChipset Features Screen Chipset Features SetupVideo Bios Shadow Security OptionWVideo Off Method Power ManagementWPM Control by APM WPower Down Activities Doze ModeWStandby Mode PCI Slot Configuration Legacy ISA Resources Controlled ByWIRQ n assigned to PCI/ISA PnPIntegrated Peripherals Load Setup Defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterDMA Channels Timer MAPSystem Resource NMI