Tyan Computer TYAN S1471 ROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC, Password Disabled

Page 36

ROM ISA BIOS

CMOS SETUP UTILITY AWARD SOFTWARE, INC.

STANDARD CMOS SETUP

BIOS FEATURES SETUP

PASSWORD SETTING

IDE HDD AUTO DETECTION

CHIPSET

FEATURES SETUP

 

DAVE & EXIT

SETUP

 

Enter Password

 

 

 

 

PCI SLOT

CONFIGURATION

 

EXIT WITH OUT SAVING

 

 

 

 

 

 

 

 

 

 

LOAD SETUP DEFAULTS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ESC : Save & Exit Setup

 

 

 

 

 

 

 

:Select Item

 

 

 

 

 

 

 

 

 

F10 : Quit

 

 

 

 

 

 

 

:Change Color

(Shift)F2

 

 

 

Change/Set/Disable Password

Type the password, up to eight characters, and press <Enter>. The password typed now will clear the previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also just press <Esc> to abort the selection and not enter a password.

To disable the password, just press <Enter> when you are prompted to enter a password. A message will confirm that the password has been disabled, the system will boot and you can enter Setup freely.

PASSWORD DISABLED

If you select System at Security Option of BIOS Features Setup Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter setup. If you select Setup at Security Option of BIOS Features Setup Menu, you will be prompted only when you try to enter setup.

S1471-001-01 http://www.tyan.com

36

 

 

 

 

 

 

 

 

 

Image 36
Contents Tyan S1471 Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1471 Board Layout RTCCPU Speed Settings for Cyrix/SGS/IBM 6x86/M1 J15 J40 J39 CPU Voltage Regulator SettingsVolts J11 Default Off Memory Voltage DIMMs Default is VoltsDefault CPU Multiplier J40 and J39 Host Bus Setting J15Reset Connector J41 Turbo LED Connector J48 Flash Eprom J50 Keylock Connector J47Cmos Resest/Password Reset J45Default off Port Setting J13 and J14 Speaker Connector J42 Turbo Switch J49Infra Red Interface Con9 and Con10 VCCSpeaker Connector Installation Turbo SwitchTurbo LED Connector Installation Hardware Reset Switch Connector Installation Refer to for Flash Eprom upgrade procedures9DRAM Installation CPU Installation Peripheral Device Installation Upgrading Cache MemoryConnecting the Power Supply GND GND VCCPage Entering Setup To Enter Setup Before Boot Press CTRL-ALT- ESC or DEL KEYPress F1 to CONTINUE, CTRL-ALT-ESC or DEL to Enter Setup Control Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuStandard Cmos setup Bios features setupChipset features setup Power Management setupStandard Cmos Setup Menu DateTime Primary/Secondary Drive type Drive a type/Drive B typeVideo EGA/VGAHalt On MemoryExpanded Memory Other MemoryBoot Sequence Swap Floppy Drive Default value is DisabledVirus warning CPU Internal Cache/External CacheBoot Up Floppy Seek Boot Up NumLock Status Default value is OnChipset Features Setup Video Bios ShadowChipset Features Screen Security OptionPower Management WPM Control by APMWVideo Off Method Doze Mode WStandby ModeWPower Down Activities PCI Slot Configuration Resources Controlled By WIRQ n assigned toLegacy ISA PCI/ISA PnPIntegrated Peripherals Load Setup Defaults Enter PasswordROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC Password DisabledIDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterTimer MAP System ResourceDMA Channels NMI