Perle Systems DS1 Connect to remote, System Default Enabled Host Name, TCP Port, Multiple Hosts

Page 79

Serial Port Profiles

General Tab Field Descriptions

The TruePort General tab determines how the TruePort connection is initiated and then sets up the appropriate connection parameters.

Configure the following parameters:

Connect to remote

When enabled, the IOLAN initiates communication to the TruePort client.

system

Default: Enabled

Host Name

The configured host that the IOLAN will connect to (must be running

 

TruePort).

 

Default: None

TCP Port

The TCP Port that the IOLAN will use to communicate through to the TruePort

 

client.

 

Default: 10001 for serial port 1, then increments by one for each serial port

Connect to

When enabled, the IOLAN will establish a connection to multiple clients

Multiple Hosts

(Hosts). When using the multiple hosts feature, all TruePort clients must be

 

running in Lite mode.

 

Default: Disabled

Define Additional

Click this button to define the hosts that this serial port will connect to. This

Hosts Button

button is also used to define the Primary/Backup host functionality.

 

See Adding/Editing Additional TruePort Hosts on page 80 for more

 

information.

Listen for

When enabled, the IOLAN will wait for connections to be initiated by the

Connection

TruePort Client.

 

Default: Disabled

TCP Port

The TCP Port that the IOLAN will use to communicate through to the TruePort

 

client.

 

Default: 10001 for serial port 1, then increments by one for each serial port

Allow Multiple

When this option is enabled, multiple hosts can connect to a serial device that

Hosts to Connect

is connected to this serial port. Note: These multiple clients (Hosts) need to be

 

running TruePort in Lite mode.

 

Default: Disabled

79

Page 78 Page 80
Image 79
Page 78 Page 80
Contents Iolan DS1/TS2 EN 55022 1998, Class A, Note Table of Contents Configuration Methods DHCP/BOOTP Getting Started Configuring Serial Ports Console Management Profile Configuring Users Configuring Security UDP Configuring the System Controlling the I/O Channels Appendix a Virtual Modem AT Commands Appendix D I/O Wiring Diagrams Appendix G Troubleshooting Documentation PrefaceAbout This Book Intended AudienceOnline Help Typeface ConventionsAbout the Iolan IntroductionIolan Family Models Hardware Iolan FeaturesSecurity SoftwareIolan Features Introduction ConnectivityIolan Components Overview Power Supply SpecificationsGetting to Know Your Iolan Desktop ModelsSerial Activity DS1End View Top ViewConsole Mode Console/Serial SwitchSerial Mode Serial Only Models Powering Up the IolanModels Configuration Methods Chapter Configures an IP Address Configuration Methods OverviewRequires a Configured IP Address Easy Config Wizard DeviceManager Access PlatformsUnique Features Connecting to the Iolan Using DeviceManagerDeviceManager Using DeviceManager WebManager Connecting to the Iolan Using WebManagerUsing WebManager Connecting to the Iolan Using the CLI Command Line InterfaceThrough the Network Through the Serial Port Using the CLIConnecting to the Iolan Using the Menu MenuUsing the Menu Using DHCP/BOOTP Connecting to the Iolan Using DHCP/BOOTPDHCP/BOOTP Parameters Snmp Connecting to the Iolan Using SnmpUsing the Snmp MIB Snmp Getting Started Easy Configuration WizardSetting Up the Network Using a Direct Serial Connection to Enable BOOTP/DHCP Using a Direct Serial Connection to Specify an IP AddressSet server internet dhcp/bootp on For an IPv6 Network Using ARP-PingSetting Up the Serial Ports Setting Up the Serial Ports Setting Up Users Using DeviceManager WebManager DeviceManager Navigating DeviceManager/WebManagerWebManager Starting a New Session Using DeviceManager to Connect to the IolanAssigning a Temporary IP Address to a New Iolan Logging in to the Iolan Adding/Deleting Manual IOLANsLogging into the Iolan Using WebManager to Connect to the IolanConfiguration Files Creating a New Iolan Configuration in DeviceManagerImporting an Existing Configuration File Opening an Existing Configuration FileManaging the Iolan Network Settings Field Descriptions IP SettingsIP Settings OverviewAdvanced Automatically server Default EnabledHost Table AdvancedFunctionality Route List Adding/Editing a HostAdding/Editing Routes Functionality Serial PortsEditing a Serial Port Resetting a Serial Port Common Tabs Serial Port ProfilesHardware Tab Field Descriptions Enable Inbound Default NoneDefault Full Default Auto Flow ControlPacket Forwarding Tab Field Descriptions Packet Size Enable Trigger1Enable Trigger2 Packet DefinitionConsole Management Profile Data Options IPv4 Address Default TelnetGeneral Tab Field Descriptions Protocol Listen for Connections on TCP PortAdvanced Tab Field Descriptions Dial Out Dial TimeoutBreak Handling DialTruePort Profile Connect to System Default Enabled Host NameConnect to remote TCP PortDefine a primary Host and backupAdding/Editing Additional TruePort Hosts Hosts to connect toAdding/Editing a Multihost Entry Backup HostPrimary Host When Signals highDay Motd Default Disabled Idle Timeout Session TimeoutTCP Sockets Profile General Tab Field Descriptions Adding/Editing Additional Hosts Adding/Editing a Multihost Entry Keepalive Enable TCPUDP Sockets Profile This entry is disabled since Direction is set to Disabled Autolearn Listen for connections on UDP port DirectionStart IP Address End IP AddressPort Default 0 zeroTerminal Profile Any PortVT320 specifically supporting VT320-7 Default DumbVT100 TVI925Automatically When any data isDay Motd Default Disabled ProtocolData Range Disconnect User logs out Default DisabledLogin Settings User Service SettingsTelnet Settings Echo InterruptQuit EraseClient Iolan Tunnel Serial Tunneling ProfileSerial Server Tunnel SerialAct As Tunnel Client Default Disabled Host NameServer Virtual Modem Profile 100 Iolan DS1/TS2 User’s Guide, Version DTR Signal Acts as RTS Signal Always On RTS Signal Acts as Phone Number to Host Mapping Host IP Address Control Signal I/O ProfileVModem Phone Number Entry Phone NumberLatch Input Signal Field DescriptionsInvert Signal DescriptionManual Clear Output Signal Field DescriptionsAuto Clear Mode Mode Default Disabled SyslogModbus Gateway Profile IP Mappings Settings Button Modbus/RTUMode Destination SlaveDefault 1000 ms Default 30 msAdvanced Field Descriptions Adding/Editing Modbus Slave IP Settings Modbus Slave IP Settings Field DescriptionsUID Start Data Options TCP or UDP Default HostDefault TCP UID EndModbus Slave Advanced Settings Field Descriptions General Tab Field Description Custom Application ProfileMonitor Advanced Serial Settings TabClosing Serial Port Default Disabled Deny Multiple NetworkAdding/Editing a Modem Modems TabName Name of the modem Field Definitions TruePort Baud Rate Tab116 Iolan DS1/TS2 User’s Guide, Version Configuring Users User Settings General Tab Adding/Editing UsersLevel Default NormalHost IP Services TabService Default DSPromptAdvanced Tab Default EnglishLanguage Sessions Tab Connect Session 1, 2, 3Serial Port Access Tab 126 Iolan DS1/TS2 User’s Guide, Version Services Configuring SecurityField Descriptions Configuring I/O InterfacesChapter Access Functionality SettingsAdvanced Slave Modbus Settings Failsafe Action is triggered Failsafe Timer FunctionalityTimeout Default 30 secondsBroadcast of I/O Default Disabled Status Enable UDPUDP Functionality UDP Entry Temperature FunctionalityUDP Settings Default CelsiusAnalog ChannelsAlarm Settings Default CurrentDigital I/O Digital InputInput Mode 139 Digital Output Output Output ModeDefault Sink Default ManualPulse Count Pulse ModeInactive Signal Width Active Signal Width DelayApplication Industrial Freezers RelayRelay I/O Monitoring Device ServerWidth Inactive SignalActive Signal Temperature Default RTD Basic Analog Alarm Settings Alarm SettingsClear Advanced Analog Alarm SettingsClear Mode Trigger TypeAnalog Data UDP Unicast FormatTotal Data Length Exists Length Data Serial Pin Signal DataUDP Unicast Example Digital/Relay DataModbus Serial Application Connected to the Serial Port Modbus SlaveModbus Serial Application Connected to the Network Modbus TCP Application Modbus I/O AccessFunction Codes Coil/Register Descriptions Input Registers Serial Port Coil/Register DescriptionsA4/T4 Registers Data Model A1/T1 A2/T2 A3/T3 A4/T4 Holding RegistersData Model D1/R1 D2/R2 Coils A4D2/A4R2 RegistersData Model Pin Coils Serial Pin SignalsD4/D2R2 Registers Data Model D3/R1 D4/R2 CoilsPC running a Modbus Serial Application TruePort Power Digital OutputTruePort I/O TruePort/Modbus CombinationAPI Over TruePort Only Power Digital OutputPC running Custom Application API TruePort Setup Accessing I/O Data Via TruePortIntroduction Response Format Format of API CommandsGet Commands Command FormatSet Commands Example 2 Turn on the first and second relay on a D2R2 unit Successful Response FormatUnsuccessful Response Format Example 1 Turn on the first relay on a D2R2 unitSnmp Traps Error CodesAlerts Configuring the System ChapterSyslog Management Custom App/Plugin Field Description Login Tab Field DescriptionsBootup Files Tab Field Descriptions Tftp Tab Field Descriptions Message of the Day Motd Tab Field DescriptionsControlling the I/O Channels Activate Output Manually activates the channel output Downloading Configuration Files System Administration ChapterManaging Configuration Files Saving Configuration FilesReboot Server Downloading Configuration Files to Multiple IOLANsServer Name Downloading Iolan Firmware Uploading Configuration FilesCalibrating I/O Calibrating Temperature InputCalibrating Analog Input Calibrating RTD Calibrating Analog ChannelsRebooting the Iolan Setting the IOLAN’s Date and TimeResetting Calibration Data Language Support Resetting the Iolan to Factory DefaultsLoading a Supplied Language Translation Guidance Software Upgrades and Language FilesCreating Terminal Definition Files Downloading Terminal DefinitionsFor example Resetting Configuration ParametersLost Admin Password 184 Iolan DS1/TS2 User’s Guide, Version Virtual Modem Initialization Commands CommandsAT&Rn AT&SnAT&Cn Serial Pinouts Pinouts and Cabling DiagramsDB25 Male DB25 Female GND CTS RJ45DB9 Male I/O DB9 Male Serial OnlyDB25 Female EIA-232 Cabling DiagramsTerminal DB25 Connector DB25 MaleDB9 Male RJ4510-pin Pin Iolan RJ45 DCE Modem DB25 ConnectorRxD TxD DTR 20 DTR GND Port Iolan Setting JumpersIolan DB25 Male/Female Iolan RJ45 DIP Digital I/O Module Analog Input Module 200 Iolan DS1/TS2 User’s Guide, Version Digital Input Dry Contact Wiring I/O DiagramsDigital I/O Digital Input Wet ContactDigital Output Source Digital Output SinkVoltage Temperature InputAnalog Input CurrentRelay Output RTD 2-WireRTD 3-Wire RTD 4-WireNormally Closed Contact 206 Iolan DS1/TS2 User’s Guide, Version TruePort TruePort UtilityAPI Request Format API I/O Access Over TruePortAPI Response Format Error Codes 210 Iolan DS1/TS2 User’s Guide, Version Starter Kit Adapters/Cable AccessoriesRJ45F DB25M DTE RJ45F to DB25M DTE Crossover AdapterRJ45F to DB25M DCE Modem Adapter RJ45F DB25F RJ45F to DB25F DTE Crossover AdapterRJ45F to DB9M DTE Crossover Adapter RJ45F to DB9F DTE Crossover Adapter Sun/Cisco RJ45M Connector Cable for Rack Mount ModelsPower/Ready LED continues to flash green in Desktop models TroubleshootingHardware Problems Communication IssuesHost Problems DeviceManager ProblemsLogin Problems Unknown IP Address Problems with TerminalsModels DHCP/BOOTP ProblemsLanguage Problems Long Reboot CycleGlossary RIP Routing PAP PasswordAuthentication Protocol Radius Remote Authentication Dial Users Services Reverse ConnectionIndex BootpSnmp
Related manuals
Manual 246 pages 24.21 Kb Manual 88 pages 61.31 Kb Manual 122 pages 55.83 Kb

DS1, TS2 specifications

Perle Systems TS2 and DS1 are advanced serial-to-Ethernet devices designed to facilitate seamless integration of serial devices with modern IP networks. These devices serve as crucial tools for businesses looking to enhance their communication capabilities while leveraging existing infrastructure.

One of the standout features of the Perle TS2 and DS1 is their ability to support multiple serial protocols including RS232, RS422, and RS485. This versatile support allows businesses to connect various legacy devices to their networks, ensuring that critical equipment can still communicate effectively in an increasingly digital landscape.

The TS2 model is particularly noted for its dual serial ports, enabling simultaneous communication with multiple devices. This capability is invaluable for applications requiring real-time data transmission, such as remote monitoring and automated control systems. The DS1 model, on the other hand, is designed for single-port use, making it an ideal solution for smaller-scale operations or specific single-device connections.

Both the TS2 and DS1 incorporate advanced features such as configuration through a web interface, which simplifies setup and management. Users can easily access device settings and monitor performance metrics remotely, enhancing operational efficiency. These devices also support various network protocols such as TCP/IP, UDP, and ICMP, ensuring compatibility with a wide range of network architectures.

In terms of security, Perle Systems prioritize user data protection. The TS2 and DS1 offer features including SSL encryption and SSH protection, providing an added layer of security for sensitive information transmitted over the network. This is particularly important for industries where data integrity and security are paramount, such as healthcare and finance.

Additionally, the rugged design of both devices ensures reliable performance even in harsh environments. With extended temperature ratings and robust housing, the TS2 and DS1 can operate in diverse conditions without compromising functionality.

To summarize, the Perle Systems TS2 and DS1 provide a reliable and flexible solution for connecting legacy serial devices to modern networks. With their support for multiple serial protocols, web-based management, robust security features, and rugged design, these devices cater to a variety of industries looking to modernize their communication infrastructure while maintaining existing equipment. Whether for large-scale operations or smaller implementations, the TS2 and DS1 equip businesses with the tools needed for effective serial communication in an IP-driven world.
Top Page Image Contents