Chapter 7 Specifications
7.1 Specifications
Power:
BATTERY POWERED
Supplied with 1 or 2 C size Lithium battery pack.
EXTERNAL POWER INPUT Voltage: 8.5 to 30 VDC Current: Less than 5 mA Supplied with 1 C size lithium battery
Protection: Reverse Polarity Protection on DC Power Input
LOOP POWERED Voltage: 8.5 to 30 VDC
Supplied with 1 or 2 C size lithium battery(ies) Protection: Reverse Polarity Protection on Current Loop Loop Burden: 8.5V maximum
BATTERY LIFE EXPECTANCY:
Expected Years of Operation for DPF500 of various powering op- tions at equipment duty cycles
MODEL |
| RUN TIME |
| |
| Idle | 2hrs/day | 8hrs/day | 24hrs/day |
10 yrs | 10 yrs | 10 yrs | 9.1 yrs | |
| 10 yrs | 10 yrs | 10 yrs | 8.4 yrs |
Standard unit | 10 yrs | 10 yrs | 10 yrs | 10 yrs |
and |
|
|
|
|
|
|
| ||
Standard unit | Indefi nite operation when externally powered | |||
and |
|
|
|
|
External or loop power
*
NOTE: Battery shelf life is rated at 10 years by manufacturer Life expectancy based on rated battery capacity at 20°C The above table is shown with pulse output inactive. Use of pulse output shortens battery life.
Example: A pulse output of 0.06 sec. duration, once per second, would derate the battery life by 20%.
DISPLAY:
Rate Display: (selectable decimal)
5 Digits (99999), 0.35" High, Display updates once per second with battery power, 8X per second with DC or Loop power
Rate Descriptors: /SEC, /MIN, /HR
Min. Input Frequency: 0.01 Hz to 10 Hz (selectable delay of 0.1 to 99.9 seconds)*
Selectable Rate Display Damping Totalizer Display: (selectable decimal)
8 Digits (99999999), 0.2" High
Totalizer Descriptors: GAL, LIT, FT3, M3, "blank"
Warning Displays: Low battery warning
PULSE OUTPUT:
The pulse output advances with the least signifi cant digit of the totalizer or decimal multiples there of (see Pulse scale divider). Type: Isolated photomos relay
Max. voltage (off state): 30 VDC
Current (on state): 100mA
Pulse Duration: Selectable 0.5, 0.25, 0.125, 0.0625 seconds
Pulse Scale divider (Pulscale): User selectable, ÷1, ÷10, ÷100 or OFF
NOTE: Select OFF for max. battery life.
ACCURACY:
0.01% Reading, ±1 count
Temperature Drift: 50 ppm/°C Worst Case
ENVIRONMENTAL:
OPERATING TEMPERATURE
+ 158°F (70°C) | |
Extended Temp: | |
HUMIDITY |
|
0 - 90% Noncondensing | |
MOUNTING STYLES: | |
1 - Panel Mount - | NEMA 4X Front |
2- Wall Mount - | NEMA 4X Enclosure |
(keypad mounted behind clear cover)
3- Explosion Proof - Class I, Division I, Groups B, C & D Class II, Division I, Groups E, F & G
INPUTS:
MAGNETIC PICKUP INPUT
Frequency Range: 0 to 3500 Hz
Trigger Sensitivity: 30 mV
Over Voltage Protected: ± 30 VDC
Low (logic 0): Less Than 1 VDC
Minimum Current: .5 mA
Hysteresis: 0.4 VDC
Frequency Range: 0 to 5 kHz
Min. Pulse Width: 0.1 msec
CONTACT CLOSURE INPUT (contact closure to common) Internal Pullup Resistor: 100 KΩ to +3.6 VDC
High (logic 1): Open or
Low (logic 0): Less Than .5 VDC
Internal Switch Debounce Filter: 0 to 40 Hz
NOTE : Sustained contact closure will shorten battery life.
RESET INPUT (contact closure to common) Internal Pullup Resistor: 100 KΩ to +3.6 VDC High (logic 1): Open or
Low (logic 0): Less Than .5 VDC
Minimum On : 25 msec
NOTE : Sustained contact closure will shorten battery life.
Range: 0.001 to 99999999
Decimal Point Locations: XXXX.XXXX to XXXXXXXX
20 POINT LINEARIZATION -LIN OPTION
This feature allows the user to enter 20 different frequencies with 20 different corresponding
ANALOG OUTPUT -MA OPTION:
Type:
Accuracy: 0.025% Full Scale at 20° C
Temperature Drift: 50 ppm/°C Typical Reverse Polarity Protected
Update Rate: 8 times/second
NOTE: The DPF500 uses the
DATA STORAGE:
Setup Information: Stored in fl ash memory
Totalizer: Stored in battery backed RAM but can be saved to fl ash memory by operator for recall after battery change out.
* A large delay setting and internal math operations may delay the update rate.
12