Omega Speaker Systems iLD Series manual Configuration Menu Remote iServer

Page 35

4.12.1 Remote iServer

It’s recommended to configure the Remote iServer and have it up and running before the Local iServer is configured.

1.A static IP address must be assigned to the Remote iServer. This means that the DHCP must remain disabled. Refer to the DHCP section of the user’s manual for details.

2.Use a browser to access the Remote iServer’s WEB page. Simply type the iServer’s IP address at the browser’s URL location (i.e. 192.168.1.50) followed by an Enter key. You should then see the iServer’s main WEB page.

3.Click on the Update button.

4.Click on Configuration, you will be prompted with a Password (default is 12345678).

5.On the Configuration page, under Serial Communication section, make sure the parameters such as Baud Rate, Data Bits, Parity, Stop Bits, Flow Control, etc. match with your attached serial device.

6.Make sure to set the End Character (Hex) to 0D and the Timeout to 500.

7.Under Terminal Server section, set Number of Connections to 1 or higher.

8.Click on Save button for the changes to take place.

Make sure that the serial cable and communication settings between the iServer and the serial device are valid.

Figure 4.21

shows the valid values that need to be set

in the Remote iServer. The Baud Rate, Data Bits, Parity, Stop Bits, Flow Control, and Transceiver values depend on what the serial device supports.

CONFIGURATION

Address http://192.168.1.50

CONFIGURATION

Serial Communication

Baud Rate 9600

 

Data Bit 7 Bits

Parity odd

Stop Bits1 bit

Flow Control none

Transciever RS-485

Modbus/TCP disable

End Character (Hex)

0D

Forward End Char enable

Timeout 0500 msecs

 

Serial Port Password

disable

1234abcd

 

 

 

Terminal Server

TCP/UDP TCP

Server Type slave

Number of Connections 1 Local Port 02000

Connection Ctrl

not used

 

Device No. 1

Connection Timeout 00100 msecs

 

Remote Access (Tunneling)

Remote Access

disable

Remote IP Address 0.0.0.0

Remote Port 02000

 

 

 

 

Save

Reset

 

 

 

 

 

Main Menu

 

Figure 4.21 Configuration Menu - Remote iServer

31

Page 34 Page 36
Image 35
Page 34 Page 36
Contents User’s Guide Servicing North America OMEGAnet On-Line Service Internet e-mail Info@omega.comTable of Contents List of Tables Rear Panel View of i16 and i8 Series Meters withManuals, Software Customer ServiceBefore You Begin Inspecting Your Shipment EMC Considerations Safety and EMC ConsiderationsPart Introduction IServer on the Ethernet Network TB4 Physical Characteristics and MountingPart Hardware Network Communication Interface Section DIP Switches on the iServerSerial Communication Interfaces For Models with RS485 Port Data Transmission Characteristics RS485Device # with RS485 Wiring RS485 InterfaceHalf Duplex Hookup TB4 Pin# ILD Big Display Network Communication Interfaces 1 10Base-T RJ-45 Pinout RJ45 Pinout 2 10Base-T Crossover WiringEthernet MAC Address Part Network ConfigurationNetwork Protocols Dhcp DIP Switch on the iServer DNSPort Number Default IP AddressIP Address Part Operations Command Prefix Command Class MeaningLSB MSB Pinging eis03ec MS-DOS Prompt IServer Home Page Menu Device TypeRead Devices Device Setpoints Read DevicesDevice Setup Modify Device Parameters or Device List Entry Device Setup10 Configuration Serial Communication ConfigurationTerminal Server Device No. Refer to Section 11 Access Control Access Control3 4 OFF Access Control Host Name Refer to .4, DNS12 Access Control Setting a New IP Address over the NetworkTerminal Server Function 13 Terminal Server Configuration14 Terminal Emulation Terminal EmulationTera Term Telnet Connection Screen Telnet Setup17 Telnet Setup iServer Help 01X01074.3 Httpget Program\iServer\Httpget\httpget -r -S *01X01\r ARP Protocol 18 ARP Commands and Responses19 PC-to-Device Communication Remote Access TunnelingRemote iServer 21 Configuration Menu Remote iServerUnder Terminal Server section, set Number of Connections to Local iServerMail Notifier Software InstallationEmail Connection Mapi Access Program Options Setup and Configuration25 iServer Mail Notifier Device Setting Device Setting and Configuration Device setup requiresInternal WEB Server Part Specifications Serial InterfaceNetwork Interface Processor CPUSerial Interface Network InterfaceAppendix a Glossary Appendix B IP Address Class C Appendix C IP NetmaskMask Dotted Notation Mask Binary Mask Bits Class a Class BDec Hex Binary Char No Parity No parity Appendix D Ascii ChartAscii Dec Hex BinaryDec Hex Ctrl Key Definition Char Equiv Appendix D Ascii Chart ContinuationAscii Control Codes Dec Hex Ctrl Key DefinitionPart Approvals Information CE Approvals Information WARRANTY/DISCLAIMER Shop on line at omega.com
Top Page Image Contents