Omega Speaker Systems iLD Series manual DIP Switches on the iServer

Page 9

2.3 DIP Switches on the iServer

For Dipswitch access you must remove the main board from the case. Refer to the Disassembly Instructions in your iLD Big Display Monitor/Controller Quickstart Manual.

1To change the IP address from the serial port

2To change to default factory settings

3To enable/disable DHCP

4 To enable/disable Terminal Server function

The iServer is shipped with all DIP switches in "OFF" position

ON

1 2 3 4 OFF

ON

1 2 3 4 OFF

Figure 2.2 DIP Switches on the iServer

Table 2.1 Rear Panel Annunciators

Serial Communication Interface Section (For Models with RS485):

TB4 Pin 3	-Rx/Tx
TB4 Pin 2	+Rx/Tx
TB4 Pin 1	Return, Common Ground Shield connection
Network Communication Interface Section:
ETHERNET	RJ45 interface for 10BASE-T connection.
RESET	Button: Used for power reseting the iServer.
COL / ACTIVITY	LED (Red) Blinking: Indicates network activities (receiving or sending packets).
ON / NET LINK	LED (Green) Solid: Indicates good network link.
TX	LED (Yellow) Blinking: Indicates transmitting data to the serial port.
RX	LED (Green) Blinking: Indicates receiving data on the serial port.

5

Image 9

Contents User’s Guide Servicing North America OMEGAnet On-Line Service Internet e-mail Info@omega.comTable of Contents List of Tables Rear Panel View of i16 and i8 Series Meters withCustomer Service Before You Begin Inspecting Your ShipmentManuals, Software Safety and EMC Considerations Part IntroductionEMC Considerations IServer on the Ethernet Network Physical Characteristics and Mounting Part HardwareTB4 Network Communication Interface Section DIP Switches on the iServerSerial Communication Interfaces For Models with RS485 Port Data Transmission Characteristics RS485Wiring RS485 Interface Half Duplex Hookup TB4 Pin# ILD Big DisplayDevice # with RS485 Network Communication Interfaces 1 10Base-T RJ-45 Pinout RJ45 Pinout 2 10Base-T Crossover WiringPart Network Configuration Network ProtocolsEthernet MAC Address Dhcp DIP Switch on the iServer DNSDefault IP Address IP AddressPort Number Part Operations Command Prefix Command Class MeaningLSB MSB Pinging eis03ec MS-DOS Prompt IServer Home Page Menu Device TypeRead Devices Device Setpoints Read DevicesDevice Setup Modify Device Parameters or Device List Entry Device Setup10 Configuration Serial Communication ConfigurationTerminal Server Device No. Refer to Section 11 Access Control Access Control3 4 OFF Access Control Host Name Refer to .4, DNS12 Access Control Setting a New IP Address over the NetworkTerminal Server Function 13 Terminal Server Configuration14 Terminal Emulation Terminal EmulationTera Term Telnet Connection Screen Telnet Setup17 Telnet Setup iServer Help Httpget Program \iServer\Httpget\httpget -r -S *01X01\r01X01074.3 ARP Protocol 18 ARP Commands and Responses19 PC-to-Device Communication Remote Access TunnelingRemote iServer 21 Configuration Menu Remote iServerUnder Terminal Server section, set Number of Connections to Local iServerMail Notifier Software InstallationEmail Connection Mapi Access Program Options Setup and Configuration25 iServer Mail Notifier Device Setting Device Setting and Configuration Device setup requiresNetwork Interface Part Specifications Serial InterfaceProcessor CPU Internal WEB ServerSerial Interface Network InterfaceAppendix a Glossary Appendix B IP Address Mask Dotted Notation Mask Binary Mask Bits Class a Appendix C IP NetmaskClass B Class CAscii Appendix D Ascii ChartDec Hex Binary Dec Hex Binary Char No Parity No parityAscii Control Codes Appendix D Ascii Chart ContinuationDec Hex Ctrl Key Definition Dec Hex Ctrl Key Definition Char EquivPart Approvals Information CE Approvals Information WARRANTY/DISCLAIMER Shop on line at omega.com