NETGEAR 7000 manual Ospf, Example #4. Enable RIP for ports 1/0/2 and 1/0/3

Page 51

NETGEAR 7000 Series Managed Switch Administration Guide

Example #4. Enable RIP for ports 1/0/2 and 1/0/3

This command sequence enables RIP for ports 1/0/2 and 1/0/3. Authentication defaults to none, and no default route entry is created. The commands specify that both ports receive both RIPv1 and RIPv2 frames, but send only RIPv2 formatted frames.

(Netgear Switch) #config

(Netgear Switch) (Config)#interface 1/0/2 (Netgear Switch) (Interface 1/0/2)#ip rip

(Netgear Switch) (Interface 1/0/2)#ip rip receive version both (Netgear Switch) (Interface 1/0/2)#ip rip send version rip2 (Netgear Switch) (Interface 1/0/2)#exit

(Netgear Switch) (Config)#interface 1/0/3 (Netgear Switch) (Interface 1/0/3)#ip rip

(Netgear Switch) (Interface 1/0/3)#ip rip receive version both (Netgear Switch) (Interface 1/0/3)#ip rip send version rip2 (Netgear Switch) (Interface 1/0/3)#exit

(Netgear Switch) (Config)#exit

OSPF

For larger networks Open Shortest Path First (OSPF) is generally used in preference to RIP. OSPF offers several benefits to the administrator of a large and/or complex network:

•Less network traffic:

–Routing table updates are sent only when a change has occurred

–Only the part of the table which has changed is sent

–Updates are sent to a multicast, not a broadcast, address

•Hierarchical management, allowing the network to be subdivided

The top level of the hierarchy of an OSPF network is known as an autonomous system (AS) or routing domain, and is a collection of networks with a common administration and routing strategy. The AS is divided into areas: intra-area routing is used when a source and destination address are in the same area, and inter-area routing across an OSPF backbone is used when they are not. An inter-area router communicates with border routers in each of the areas to which it provides connectivity.

The 7000 Series Managed Switch operating as a router and running OSPF will determine the best route using the assigned cost and the type of the OSPF route. The order for choosing a route if more than one type of route exists is as follows:

IP Routing Services

5-15

v1.1, May 2006

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Netgear 7000 Series Managed Switch Administration Guide Certificate of the Manufacturer/Importer TrademarksStatement of Conditions EN 55 022 Declaration of ConformanceRegulatory Compliance Information FCC Information to UserFCC Guidelines for Human Exposure Declaration Of ConformityProduct and Publication Details Series Managed SwitchContents Link Aggregation Chapter Virtual Router Redundancy Protocol Chapter Differentiated Services Chapter Pre-Login Banner Chapter Syslog Document Organization About This BookCLI Documentation AudienceRelated Documentation Xiv In-band and Out-of-band Connectivity Configuring for In-band ConnectivityUsing BootP or Dhcp Chapter Getting StartedUsing the EIA-232 Port Configuring for Out-Of-Band Connectivity Initial Configuration Starting the SwitchInitial Configuration Procedure Software Installation System Information and System SetupQuick Starting the Networking Device Quick Start Commands Mode Description You power down or reset the networking device. In a stacking Quick Start Commands Figurations made to the networking device Configuring for Web Access Chapter Using the Web InterfaceConfiguring an Snmp V3 User Profile Starting the Web InterfaceWeb Page Layout Save Command ButtonsNetgear 7000 Series Managed Switch Administration Guide Chapter Virtual LANs Vlan Configuration Example CLI ExamplesExample #1 Create Two VLANs Example #4 Assign VLAN3 as the Default Vlan Example #2 Assign Ports to VLAN2Example #3 Assign Ports to VLAN3 Graphical User Interface CLI Example Link Aggregation1shows the example network STP Example 1 Create two LagsExample 2 Add the ports to the LAGs Example 3 Enable both LAGsPort Routing Chapter IP Routing ServicesPort Routing Configuration CLI Examples Example 1. Enabling routing for the SwitchVlan Routing Example 2. Enabling Routing for Ports on the SwitchVlan Routing Configuration Example 1 Create Two VLANs Example 2 Set Up Vlan Routing for the VLANs and the SwitchVlan Routing RIP Configuration CLI Example Netgear 7000 Series Managed Switch Administration Guide Vlan Routing Ospf Configuration Netgear 7000 Series Managed Switch Administration Guide Routing Information Protocol RIP ConfigurationCLI Example Example #1 Enable Routing for the SwitchExample #3. Enable RIP for the Switch Example #2 Enable Routing for PortsOspf Example #4. Enable RIP for ports 1/0/2 and 1/0/3CLI Examples Example #1 Configuring an Inter-Area Router Netgear 7000 Series Managed Switch Administration Guide Example #2 Configuring Ospf on a Border Router Enable routing for the switch Overview Proxy Address Resolution Protocol ARPExample #2 ip proxy-arp Example #1 show ip interfaceChapter Virtual Router Redundancy Protocol Virtual Router Redundancy Protocol Enable Vrrp for the switch Set the priority for the port. The default priority is Limitations Chapter Access Control Lists ACLsOverview MAC ACLsConfiguring IP ACLs IP ACL CLI Example ProcessMAC ACL CLI Examples Example #1 mac access list Example #2 permit any Example #3 Configure mac access-group Example #4 permit Example #5 show mac access-lists Netgear 7000 Series Managed Switch Administration Guide Chapter Class of Service CoS Queuing CoS Queue MappingTrusted Ports CoS Queue Configuration Port Egress Queue ConfigurationUntrusted Ports Per Interface Basis Drop Precedence Configuration per QueueExample #2 set classofservice trust mode Example #1 show classofservice trustExample #3 show classofservice ip-precedence mapping Traffic Shaping Example #5 Set CoS Trust Mode of an InterfaceExample #1 traffic-shape Netgear 7000 Series Managed Switch Administration Guide Chapter Differentiated Services Differentiated Services Netgear Switch Config#diffserv DiffServ for VoIP Configuration Example Netgear 7000 Series Managed Switch Administration Guide Following example configures DiffServ VoIP support Chapter Igmp Snooping Example #1 Enable Igmp SnoopingExample #3 show mac-address-table igmpsnooping Example #2 show igmpsnoopingChapter Port Security Operation Example #3 Config port security Example #1 show port securityExample #2 show port security on a specific interface 11-4 Port Security Chapter Traceroute 12-2 Traceroute Considerations Chapter Configuration ScriptingExample #3 script apply running-config.scr Example #1 scriptExample #2 script list and script delete Example #5 Upload a Configuration Script Example #4 Creating a Configuration Script13-4 Configuration Scripting Chapter Outbound Telnet Example #2 show telnet Example #1 show networkExample #3 transport output telnet Example #4 session-limit and session-timeout14-4 Outbound Telnet Port Mirroring Example #1 show monitor session Example #2 show port allExample #3 show port interface Port, and what is enabled or disabled on the port Example #4 Config monitor session 1 modeExample #6 Interface port security Example #5 Config monitor session 1 source interfaceExample #1 show sntp Simple Network Time Protocol SntpExample #4 Configure Sntp Example #2 show sntp clientExample #3 show sntp server Simple Network Time Protocol Sntp 16-3 16-4 Simple Network Time Protocol Sntp Chapter Pre-Login Banner Transfer the file from the PC to the switch using Tftp Persistent Log Files Chapter SyslogInterpreting Log Files Example #2 show logging buffered Example #1 show loggingExample 4 show logging hosts Example #3 show logging traplogsExample #5 logging port configuration 18-6 Syslog
Related manuals
Manual 2 pages 6.29 Kb

7000 specifications

The NETGEAR Nighthawk R7000 is a high-performance dual-band Wi-Fi router that stands out in the crowded market of home networking devices. Designed to cater to gamers, streamers, and smart home enthusiasts, it provides robust connectivity and a range of features aimed at ensuring seamless internet experiences.

One of the R7000’s standout features is its dual-band capability, which allows it to operate on both the 2.4 GHz and 5.0 GHz frequency bands. This flexibility offers users the ability to connect devices that require stable connections without interference, such as smart TVs, gaming consoles, and smartphones. With speeds of up to 1900 Mbps, the R7000 supports even the most bandwidth-intensive activities, enabling multiple devices to stream, game, and browse simultaneously without lag.

The router is powered by a powerful dual-core processor, which enhances its overall performance and allows for efficient multitasking. With the inclusion of Beamforming technology, the R7000 intelligently directs Wi-Fi signals toward connected devices instead of broadcasting them in all directions. This focused connection improves network efficiency and range, ensuring that users can maintain strong links even in larger homes.

Security is a paramount concern for NETGEAR, and the R7000 addresses this with robust features. It includes built-in NETGEAR Armor, an advanced cybersecurity solution that protects connected devices from online threats. Additionally, parental controls and guest network options provide users with enhanced privacy and management capabilities, allowing families to regulate internet access and safeguard their networks.

The device is compatible with Amazon Alexa and Google Assistant, providing users with the ability to control their networks through voice commands. The R7000 also supports ReadySHARE USB access, enabling easy file sharing between devices by simply connecting a USB storage device to the router.

Setup and management of the R7000 are straightforward, thanks to the intuitive NETGEAR Nighthawk app. This mobile application allows users to manage their Wi-Fi settings, monitor connected devices, and perform speed tests on-the-go.

In summary, the NETGEAR Nighthawk R7000 is a feature-rich router designed for demanding internet users, combining speed, security, and user-friendly management to enhance the overall connectivity experience. Whether for gaming, streaming, or managing smart homes, the R7000 remains a strong contender in the networking landscape.
Top Page Image Contents