NETGEAR 7000 manual Vlan Routing, Example 2. Enabling Routing for Ports on the Switch

Page 40

NETGEAR 7000 Series Managed Switch Administration Guide

Example 2. Enabling Routing for Ports on the Switch

Use the following commands to enable routing for ports on the switch. The default link-level encapsulation format is Ethernet. Configure the IP addresses and subnet masks for the ports. Network directed broadcast frames will be dropped and the maximum transmission unit (MTU) size will be 1500 bytes.

(Netgear Switch) #config

(Netgear Switch) (Config)# interface 1/0/2 (Netgear Switch) (Interface 1/0/2)#routing

(Netgear Switch) (Interface 1/0/2)#ip address 192.150.2.1 255.255.255.0 (Netgear Switch) (Interface 1/0/2)#exit

(Netgear Switch) (Config)#interface 1/0/3 (Netgear Switch) (Interface 1/0/3)#routing

(Netgear Switch) (Interface 1/0/3)#ip address 192.150.3.1 255.255.255.0 (Netgear Switch) (Interface 1/0/3)#exit

(Netgear Switch) (Config)#interface 1/0/5 (Netgear Switch) (Interface 1/0/5)# routing

(Netgear Switch) (Interface 1/0/5)#ip address 192.150.5.1 255.255.255.0 (Netgear Switch) (Interface 1/0/5)#exit

(Netgear Switch) (Config)#exit

VLAN Routing

You can configure 7000 Series Managed Switch with some ports supporting VLANs and some supporting routing. You can also configure it to allow traffic on a VLAN to be treated as if the VLAN were a router port.

When a port is enabled for bridging (the default) rather than routing, all normal bridge processing is performed for an inbound packet, which is then associated with a VLAN. Its MAC Destination Address (DA) and VLAN ID are used to search the MAC address table. If routing is enabled for the VLAN and the MAC DA of an inbound unicast packet is that of the internal bridge-router interface, the packet will be routed. An inbound multicast packet will be forwarded to all ports in the VLAN, plus the internal bridge-router interface if it was received on a routed VLAN.

Since a port can be configured to belong to more than one VLAN, VLAN routing might be enabled for all of the VLANs on the port, or for a subset. VLAN Routing can be used to allow more than one physical port to reside on the same subnet. It could also be used when a VLAN spans multiple physical networks, or when additional segmentation or security is required.

5-4

IP Routing Services

v1.1, May 2006

Image 40
Contents Netgear 7000 Series Managed Switch Administration Guide Trademarks Statement of ConditionsEN 55 022 Declaration of Conformance Certificate of the Manufacturer/ImporterFCC Information to User FCC Guidelines for Human ExposureDeclaration Of Conformity Regulatory Compliance InformationSeries Managed Switch Product and Publication DetailsContents Link Aggregation Chapter Virtual Router Redundancy Protocol Chapter Differentiated Services Chapter Pre-Login Banner Chapter Syslog About This Book Document OrganizationAudience CLI DocumentationRelated Documentation Xiv Configuring for In-band Connectivity Using BootP or DhcpChapter Getting Started In-band and Out-of-band ConnectivityUsing the EIA-232 Port Configuring for Out-Of-Band Connectivity Starting the Switch Initial ConfigurationInitial Configuration Procedure System Information and System Setup Software InstallationQuick Starting the Networking Device Quick Start Commands Mode Description You power down or reset the networking device. In a stacking Quick Start Commands Figurations made to the networking device Chapter Using the Web Interface Configuring for Web AccessStarting the Web Interface Configuring an Snmp V3 User ProfileWeb Page Layout Command Buttons SaveNetgear 7000 Series Managed Switch Administration Guide Chapter Virtual LANs CLI Examples Vlan Configuration ExampleExample #1 Create Two VLANs Example #2 Assign Ports to VLAN2 Example #4 Assign VLAN3 as the Default VlanExample #3 Assign Ports to VLAN3 Graphical User Interface Link Aggregation CLI Example1shows the example network Example 1 Create two Lags STPExample 3 Enable both LAGs Example 2 Add the ports to the LAGsChapter IP Routing Services Port RoutingPort Routing Configuration Example 1. Enabling routing for the Switch CLI ExamplesExample 2. Enabling Routing for Ports on the Switch Vlan RoutingVlan Routing Configuration Example 2 Set Up Vlan Routing for the VLANs and the Switch Example 1 Create Two VLANsVlan Routing RIP Configuration CLI Example Netgear 7000 Series Managed Switch Administration Guide Vlan Routing Ospf Configuration Netgear 7000 Series Managed Switch Administration Guide RIP Configuration Routing Information ProtocolExample #1 Enable Routing for the Switch CLI ExampleExample #2 Enable Routing for Ports Example #3. Enable RIP for the SwitchExample #4. Enable RIP for ports 1/0/2 and 1/0/3 OspfCLI Examples Example #1 Configuring an Inter-Area Router Netgear 7000 Series Managed Switch Administration Guide Example #2 Configuring Ospf on a Border Router Enable routing for the switch Proxy Address Resolution Protocol ARP OverviewExample #1 show ip interface Example #2 ip proxy-arpChapter Virtual Router Redundancy Protocol Virtual Router Redundancy Protocol Enable Vrrp for the switch Set the priority for the port. The default priority is Chapter Access Control Lists ACLs OverviewMAC ACLs LimitationsConfiguring IP ACLs Process IP ACL CLI ExampleMAC ACL CLI Examples Example #1 mac access list Example #2 permit any Example #3 Configure mac access-group Example #4 permit Example #5 show mac access-lists Netgear 7000 Series Managed Switch Administration Guide CoS Queue Mapping Chapter Class of Service CoS QueuingTrusted Ports Port Egress Queue Configuration CoS Queue ConfigurationUntrusted Ports Drop Precedence Configuration per Queue Per Interface BasisExample #1 show classofservice trust Example #2 set classofservice trust modeExample #3 show classofservice ip-precedence mapping Example #5 Set CoS Trust Mode of an Interface Traffic ShapingExample #1 traffic-shape Netgear 7000 Series Managed Switch Administration Guide Chapter Differentiated Services Differentiated Services Netgear Switch Config#diffserv DiffServ for VoIP Configuration Example Netgear 7000 Series Managed Switch Administration Guide Following example configures DiffServ VoIP support Example #1 Enable Igmp Snooping Chapter Igmp SnoopingExample #2 show igmpsnooping Example #3 show mac-address-table igmpsnoopingChapter Port Security Operation Example #1 show port security Example #3 Config port securityExample #2 show port security on a specific interface 11-4 Port Security Chapter Traceroute 12-2 Traceroute Chapter Configuration Scripting ConsiderationsExample #1 script Example #3 script apply running-config.scrExample #2 script list and script delete Example #4 Creating a Configuration Script Example #5 Upload a Configuration Script13-4 Configuration Scripting Chapter Outbound Telnet Example #1 show network Example #2 show telnetExample #4 session-limit and session-timeout Example #3 transport output telnet14-4 Outbound Telnet Port Mirroring Example #2 show port all Example #1 show monitor sessionExample #3 show port interface Example #4 Config monitor session 1 mode Port, and what is enabled or disabled on the portExample #5 Config monitor session 1 source interface Example #6 Interface port securitySimple Network Time Protocol Sntp Example #1 show sntpExample #2 show sntp client Example #4 Configure SntpExample #3 show sntp server Simple Network Time Protocol Sntp 16-3 16-4 Simple Network Time Protocol Sntp Chapter Pre-Login Banner Transfer the file from the PC to the switch using Tftp Chapter Syslog Persistent Log FilesInterpreting Log Files Example #1 show logging Example #2 show logging bufferedExample #3 show logging traplogs Example 4 show logging hostsExample #5 logging port configuration 18-6 Syslog
Related manuals
Manual 2 pages 6.29 Kb

7000 specifications

The NETGEAR Nighthawk R7000 is a high-performance dual-band Wi-Fi router that stands out in the crowded market of home networking devices. Designed to cater to gamers, streamers, and smart home enthusiasts, it provides robust connectivity and a range of features aimed at ensuring seamless internet experiences.

One of the R7000’s standout features is its dual-band capability, which allows it to operate on both the 2.4 GHz and 5.0 GHz frequency bands. This flexibility offers users the ability to connect devices that require stable connections without interference, such as smart TVs, gaming consoles, and smartphones. With speeds of up to 1900 Mbps, the R7000 supports even the most bandwidth-intensive activities, enabling multiple devices to stream, game, and browse simultaneously without lag.

The router is powered by a powerful dual-core processor, which enhances its overall performance and allows for efficient multitasking. With the inclusion of Beamforming technology, the R7000 intelligently directs Wi-Fi signals toward connected devices instead of broadcasting them in all directions. This focused connection improves network efficiency and range, ensuring that users can maintain strong links even in larger homes.

Security is a paramount concern for NETGEAR, and the R7000 addresses this with robust features. It includes built-in NETGEAR Armor, an advanced cybersecurity solution that protects connected devices from online threats. Additionally, parental controls and guest network options provide users with enhanced privacy and management capabilities, allowing families to regulate internet access and safeguard their networks.

The device is compatible with Amazon Alexa and Google Assistant, providing users with the ability to control their networks through voice commands. The R7000 also supports ReadySHARE USB access, enabling easy file sharing between devices by simply connecting a USB storage device to the router.

Setup and management of the R7000 are straightforward, thanks to the intuitive NETGEAR Nighthawk app. This mobile application allows users to manage their Wi-Fi settings, monitor connected devices, and perform speed tests on-the-go.

In summary, the NETGEAR Nighthawk R7000 is a feature-rich router designed for demanding internet users, combining speed, security, and user-friendly management to enhance the overall connectivity experience. Whether for gaming, streaming, or managing smart homes, the R7000 remains a strong contender in the networking landscape.