NetComm IG6000 manual Legal & Regulatory Information, Copyright Information

Page 4

Industrial Modem User Guide

Legal & Regulatory Information

Copyright Information

This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior written permission of NetComm Limited.

NetComm Limited accepts no liability or responsibility, for consequences arising from the use of this product.

NetComm limited reserves the right to change the specifications and operating details of this product without notice.

NetComm is a registered trademark of NetComm Limited.

All other trademarks are acknowledged the property of their respective owners.

Australian Customer Information

Austel (The Australian Telecommunications Authority) requires you to be aware of the following information and warnings:

Users may experience minor audio distortion when using this product. This distortion may be generated by the low bit rate for voice sampling.

Some of the modem default settings have been selected to comply with Austel technical specifications. If you intend to change any default settings you must comply with the following rules:

1.The modem must not answer an incoming call less than two seconds after the first ring signal. As a Òrule­of­ thumbÓ your modem should be set so it answers incoming calls after the second ring (ATS0=2).

2.If Busysignal detection is switched off, the modem must not attempt more than two automatic redials and must wait at least two seconds before redialling.

3.If Busy signal detection is switched on, the modem must not attempt more than nine automatic redials and must wait at least two seconds before redialling.

4.If, after redialling the maximum number of times, the modem is still unable to establish a connection you must wait 30 minutes before attempting to redial.

5.The use of Bell standard 103 and 212A is not permitted in Australia. Use of these modes will cause your modem to lose its permit status.

Changing the default values of the modem, in such a way as to cause your modem to operate in a non­compliant manner when connected to a telecommunications network operated by a carrier, is contrary to the Telecommunications Act 1991 and may result in penalties of $12,000.

New Zealand Customer Information

New Zealand Telecom requires you to be aware of these important warnings:

This equipment may not necessarily provide for the effective hand­over of a call to or from a telephone connected to the same line.

The operation of this equipment on the same line as telephones or other equipment with audible warning devices or automatic ring detectors will give rise to bell tinkle or noise and may cause false tripping of the ring detector. Should such problems occur, the user is not to contact Telecom Faults Service.

The telephone associated with the authorised apparatus must be permitted for connection to the New Zealand public telephone network.

The transmit level from this device is set at a fixed level and because of this there may be circumstances where the device does not give its optimum performance. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and do not report a fault unless the telephone performance is impaired.

YML391­3A

4

Image 4 Contents
Industrial Modem Table of Contents Contact Information Technical SupportTeleMarketing Mailing ListLegal & Regulatory Information Copyright InformationAustralian Customer Information New Zealand Customer InformationIndustrial Modem User Guide Introduction Modem Controls and Indicators Links Internal controlsPstn OUTPower Down Feature Modem FeaturesDial and Talk Feature How to Load the Voice Alarm Messages Voice Messaging SystemAT#MEM1 AT#MEM2Remote Voice Setting of Alarm Messages Asynchronous Mode Synchronous ModeOperating Modes Line SpeedsLeased Line Operation Commands Modem AT CommandsDial Modifiers General Commands Speaker on during dial, answer, retrain or rate change #MEM0 #MEM1#MEM2 #MINIIndustrial Modem User Guide Modulation Setting Mod Modulation Possible Rates bpsAT­SDR=0 Distinctive RingAT­SDR=7 Response Codes Registers AsciiSpecifications Data Compression EncryptionEnvironmental Humidity