Nvidia 754 specifications Chipset IDE Devices

Page 41

BIOS

Chipset IDE Devices

Scroll to Chipset IDE Devices and press <Enter>. The following screen appears:

Delay For HDD (Secs)

This item allows you to set longer time stand by before system Scan HDD at post screen. Some HDD may need a longer stand by time before it can be detected.

Options: 0 ~ 15.

OnChip IDE Channel 0/1

The mainboard supports two channel of ordinary IDE interface and one channel of serial ATA interface. Select “Enabled” to activate each channel separately.

If you do not use the onboard IDE connector, set the Onboard Primary (Secondary) PCI IDE to “Disabled”.

Primary/Secondary Master/Slave UDMA

Select the mode of operation for the IDE drive. Ultra DMA-100/133 implemen- tation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver. If your hard drive and your system software both support Ultra DMA-100/133, select Auto to enable UDMA mode by BIOS. Options: Auto, Disabled.

SATA 3/4

This item enables/disables the S-ATA3/4 ports.

SATA 1/2

This item enables/disables the S-ATA1/2 ports.

RAID Enable

This item allows you to select the RAID mode. When set to “Enabled” the four fields become available to set RAID for each SATA.

Options: Enabled, Disabled.

Page 4-11

Image 41
Contents Manual Revision August 30 Disclaimer of Warranties Post Port Frequently Asked Questions Table of Contents Section RAID Configuration Left Blank Introduction Mainboard Features RAID function available on chipset S-ATA/S-ATA II ports Special Features Bios Features Magic Health System Block Diagram Introduction Mainboard Specification Processor SpecificationChipset Main MemoryAt Rear Panel AudioPeripheral Interfaces Front Panel Controller Onboard connector and pin-headerSpecial Features Form Factor Mainboard Layout InstallationStep Installation Easy Installation ProcedureCPU Installation Installation Installation Jumper Settings Memory Installation Installation System Memory Configuration Memory LayoutMemory configurations supported Installation VGA Card Installation Installation Jcpufan / Jpwrfan / Jsysfan Installation Device ConnectorsPW1 CD-INAUX-IN CUSB3/CUSB4/CUSB5 Six USB 2.0 ports EZ-Button RESET, PW-ONCFP CIR Cspk Simple ATX power ON/OFF controller Installation Power-On/Off RemoteInstallation Main Menu To enter the Setup ProgramStandard Cmos Setup Standard Cmos SetupBios Features Setup Advanced Bios FeaturesInit Display First Security Option Chipset Features Setup Advanced Chipset FeaturesFor setting Dram command rate timing Options Auto, 1T, 2T Options Auto, 2.5ns to 9.5ns in 0.5ns increments Options Auto, 1ns ~ 15ns Integrated Peripherals Integrated PeripheralsChipset IDE Devices Onboard Device Legacy Devices Power Management Power Management SetupPNP/PCI/PCI-E Configuration Setup PNP/PCI/PCI-E ConfigurationInterrupt requests are shared as shown below PCI Express related itemsPC Health Status PC Health StatusVoltage level of the 5V Standby Smart Fan example Frequency/Voltage Control Power Bios FeaturesPcie Clock Load Optimized Defaults Defaults MenuLoad Fail-Safe Defaults Supervisor/User Password Setting Enter PasswordSave & Exit Setup Exiting BiosSave to Cmos and Exit Y/N? Y Exit Without SavingRAID Basics RAID ConfigurationIntroduction RAID 0 Striping RAID Configuration NVidia RAID Features Enable RAID ROM RAID Configuration Enable RAID FunctionPrepare driver floppy RAID Configuration Create RAID ArrayInstall Software utility for Windows Install O/S into RAID diskEasy Driver Installation Driver InstallationSound Effect Driver Installation Realtek Sound Manager Quick User-guideSpeaker Configuration Driver Installation EqualizerConnector Sensing Driver Installation Speaker TestDriver Installation Connector Sensing Microphone Driver Installation Hrtf DemoDriver Installation General Driver Installation Appendix Update Your System BiosKey in File Name to save previous Bios to file Using the Define a New Array Window Nvidia RAID Bios UtilityCompleting the RAID Bios Setup Appendix Appendix Appendix C Appendix Appendix If password is set, ask for password