Multi-Tech Systems FR2201 manual Appendix a Cabling Diagrams Command Port Cable, LAN Cables

Page 62

MultiFRAD II User Guide

Appendix A - Cabling Diagrams

Command Port Cable

13

12

11

10

9

8

7

6

5

4

3

2

1

25 24 23 22 21 20 19 18 17 16 15 14

COMMAND PORT

To COMMAND PORT Connector

PIN NO.	PIN NO.
1	1
2	2
3	3
4	4
5	5
6	6
7	7
8	8
20	20
22	22
25	25

	TRANSMIT DATA (BA)	To
	RECEIVE DATA (BB)	To
	RECEIVE DATA (BB)	DTE
		DTE
		Device
		(Terminal
		Device
		i.e. ASCII
	SIGNAL GROUND (AB)	Terminal)

LAN Cables

1 2 3 4 5 6 7 8

10BASE-T

ETHERNET

8

7

6

5

4

3

2

1

15 14 13 12 11 10 9

AUI

	10Base-T (RJ-45)			AUI (DB-15)
Pin	Circuit Signal Name		Pin	Circuit Signal Name
1	TD+	Data Transmit Positive	1	CO-S	Control In Circuit Shield
2	TD-	Data Transmit Negative	2	CI+	Control In Positive
3	RD+	Data Receive Positive	3	DO+	Data Out Positive
4	RD-	Data Receive Negative	4	DIS	Data In Circuit Shield
			5	DI+	Data In Circuit Positive
			6	VC	Voltage common
			7	CO+	Control Out Pos (optional)
			8	COS	Control Out Shld (optional)
			9	CI-	Control In Negaative
			10	DO-	Data Out Negative
			11	DO-S	Data Out Circuit Shield
			12	DI-	Data In Negative
			13	VP	Voltage Plus
			14	VS	Voltage Shield
			15	CO-	Control Out Neg (optional)
			Shell	PG	Protective Ground

62

Image 62

Contents User Guide User Guide Contents Appendixes Introduction and Description Introduction MultiFRADPreview of this Guide Introduction and DescriptionFront Panel Description EthernetEthernet AUI Connector Back Panel DescriptionShunts ShuntsTechnical Specifications Data PortsMultiFRAD II User Guide Installation Unpacking your MultiFRAD UnpackingCabling Procedure Step Procedure Cabling your MultiFRADMultiFRAD II User Guide Software Loading and Configuration Installing your Software Choose Destination Location screen is displayedSoftware Loading and Configuration MultiFRAD II User Guide Software Loading and Configuration MultiFRAD II User Guide Software Loading and Configuration MultiFRAD II User Guide MultiFRAD Software Download User Defaults Before You BeginDownload Firmware MultiFRAD Configuration Setup MenuIP Setup MultiFRAD II User Guide IPX Setup MultiFRAD II User Guide Spanning Tree Setup Statistics IP Statistics IPX Port Statistics STP Spanning Tree Port StatisticsSnmp Statistics WAN Statistics Frame Relay StatisticsData Port Statistics WAN Port Setup Point to Point Setup Frame Relay Setup MultiFRAD Software MultiFRAD II User Guide MultiFRAD Software Data Port Configuration Remote Configuration and Management Modem-Based Remote Configuration Procedure Remote Configuration and Management MultiFRAD II User Guide Telnet MultiFRAD Management Remote User Database Web Browser Management Warranty, Service and Tech Support Limited Warranty On-line Warranty RegistrationContacting Tech Support via E-mail Tech SupportRecording MultiFRAD Information Service To Download a file Multi-Tech BBSTo log on to the Multi-Tech BBS About the Internet About the Multi-Tech Fax-Back ServiceAbout CompuServe Appendixes Appendix a Cabling Diagrams Command Port Cable LAN CablesTrunk Cable RS232C/V.24 * Link CableRemote Configuration Cable Command PortAppendix B Regulatory Information Appendix C Network Overview Figure B-1. OSI Protocol StackPacket Network Address Internet Protocol IPIP Addressing MultiFRAD II User Guide Glossary MultiFRAD II User Guide Glossary MultiFRAD II User Guide Glossary MultiFRAD II User Guide Glossary MultiFRAD II User Guide Glossary MultiFRAD II User Guide Subscriber Loop See Local loop MultiFRAD II User Guide Glossary About the Multi-TechFax-Back Service Recording MultiFRAD Information