Multi-Tech Systems MR9600 manual Introduction, Installation Procedure

Page 16

MR9600 User Guide

Introduction

This chapter describes how to install the MR9600 Controller into a CommPlete Communication Server CC9600 chassis. This equipment should only be installed by properly qualified service personnel.

The MR9600 Controller assembly consists of the MR9600 Controller card, an integrated Ethernet concentrator card, and a common front panel. Figure 3 shows the layout of the MR9600 card without the concentrator. The MR9600 assembly plugs into bus connectors on the inside of the CC9600 chassis. Three communications connectors on the concentrator module are accessible from the back of the CC9600 chassis: a DB-9 serial connector for MR9600 diagnostics and configuration, and two Ethernet 10Base-T connectors for network access.

Reset

LEDs

Test

RAM

RAM

U6

 

U7

 

U5

 

U4

 

 

 

 

 

 

 

Flash Memory

CPU

Connectors

To back panel config/ debug port

Figure 3. MR9600 Controller card. Ethernet concentrator module not shown.

Installation Procedure

1.Unpack the MR9600 assembly from its packaging, and save the packaging for possible future use. Perform a visual inspection of the MR9600. If you are concerned about the condition of the MR9600, call Technical Support for instructions.

2.Remove the blank controller panel or previous MR9600 controller from the CC9600 chassis. The MR9600 is hot-swappable.

3.Holding the MR9600 by its handle and the edges of the bottom panel, place the MR9600 into the open controller slot of the CC9600. Make sure the edges of the MR9600 card mate properly with the plastic guides in the CC9600.

4.Slide the MR9600 into the CC9600 chassis until you feel the MR9600’s connectors fit into the bus connectors at the back of the CC9600.

5.Tighten the MR9600's retaining screws.

6.Turn on the PS9600 power supplies, if they are off.

7.Note the PS9600 LED indicators. If they are not lit, see Chapter 6. If they are lit, proceed with MultiCommManager operation (Refer to the MultiCommManager User Guide).

Note: A self-test runs each time the CommPlete Communications Server is turned on. Refer to the

MultiCommManager User Guide for more details on the power-on self-test.

8

CommPlete Communications Server

Page 15 Page 17
Image 16
Page 15 Page 17
Contents MR9600 Controller User Guide Page Page Page CommPlete Communications Server CommPlete Communications Server Table of Contents Solving Problems Introduction LED Indicators IntroductionProduct Description Card Status LEDsEthernet Status LEDs IntroductionConnectors Concentrator LEDsSpecifications MR9600 User Guide Installation Installation Procedure Ethernet Cabling Serial CablingMR9600 User Guide Quick Start Turn off all power to the CommPlete chassis MR9600 Quick StartSelect Setup Snmp Mode Supervisor Select option 3, Configuration of RASExpressSupervisor Console Quick Start Operation File System SecurityEvent Files Command Line Interface Snmp InterfaceTelnet Interface Web Browser InterfaceLogging Getting Modem InformationFTP Interface Web Interface LimitationsOperation Page Commands Examples Parameter TypesExample Commands Listed by Function DisplayFile Modem Control System Commands Listed by Security Level GuestOperator Supervisor Command Reference ModulesParameter None Security Guest ExampleSecurity Guest Parameter None AbortSecurity Operator Example Boot BpstatusBye Security Supervisor ExampleCfg, configure Cat, typeCd, chdir ChdirConfigure Cl, clockCopy, cp DateDownload Dir, lsSecurity Supervisor E1cfg E1setupE1channelstatus, e1chstatus Exit E1statusFormat Getdevices GetcallsGete1 Getfaults Getfkey1, getfkey2, getfkey3, getfkey4Getgateway GetipGetpowerstatus, getps GetmodemsGetprichannels GetpriGetrack Getras GetreadcommunityGetsendtrap GetslotsGetsubnet Gett1Gettemp GettrapGetwritecommunity HaltsysHistory ListmodLo, logout LoadmodMd, mkdir MoreOc, oosclear, oosclr MountOnline Oosset, os Passwd, passwordPing Poweron PoweroffPriocbchannels Prisetup PriosbchannelsPristatus RassetupQuit Rasstatus Rd, remdirReset, rs ReadmeRen, rename RendirSe, setenviron SecuritySetconfig Setfkey1, setfkey2, setfkey3, setfkey4Setgateway SetipSetpollingoff SetpollingonSetreadcommunity SetsendtrapSetsubnet Parameter On, offSettrap SetwritecommunitySync TimeT1cfg T1channelstatus, t1chstatusT1debug Security Supervisor Limitation CC9600 only ExampleT1setup T1statusUpdate TypeUnloadmod UnmountUpload UptimeUserid UsageVer, version Whoami Error Messages Error No history is being maintained Error Password not changedError Unknown error Error Bad or missing configuration fileMR9600 User Guide Solving Problems Introduction MR9600 Diagnostic Tests Solving Problems MR9600 User Guide Appendix Appendix a Updating the MR9600 Controller Firmware Index MR9600 User Guide Index IP address mask parameter IP address parameter

MR9600 specifications

Multi-Tech Systems MR9600 is a versatile and powerful device tailored for today's diverse communication needs, featuring advanced technology that ensures reliable connectivity and performance. This multi-purpose communication platform is primarily designed for applications in the Internet of Things (IoT), machine-to-machine (M2M) communications, and various telecommunication systems, providing seamless data transmission across multiple networks.

One of the standout features of the MR9600 is its integrated 4G LTE capability, offering high-speed cellular connectivity. This ensures that users can maintain uninterrupted communication regardless of their geographic location. The device supports a wide range of LTE bands, making it compatible with numerous cellular networks worldwide. Additionally, the MR9600 is equipped with fall-back support for 3G networks, providing a safety net for areas with limited 4G coverage.

The MR9600 is designed with a variety of interfaces, including Ethernet, serial, and USB ports, allowing for easy integration with legacy systems and modern devices. This flexibility ensures that the MR9600 can be deployed in numerous environments, from industrial automation to smart city applications, making it a go-to solution for system integrators and developers looking to enhance connectivity.

Security is another essential aspect of the MR9600, featuring built-in security protocols that protect data transmission and device integrity. With secure access controls, including VPN and firewall capabilities, users can rest assured that their information remains safe from potential threats.

Furthermore, the MR9600 supports over-the-air (OTA) firmware updates, allowing for streamlined management and maintenance of devices in the field. This feature reduces downtime and enhances operational efficiency, enabling businesses to scale their IoT deployments effortlessly.

In summary, the Multi-Tech Systems MR9600 combines advanced 4G LTE technology, multiple connectivity options, and robust security features to deliver a reliable and efficient communication solution. Its versatility makes it suitable for a wide array of applications, solidifying its place as a leading choice for enterprises looking to optimize their communication capabilities in an increasingly connected world.
Top Page Image Contents