Multi-Tech Systems MR9600 manual Getsubnet, Gett1, Gettemp, Gettrap

Page 51

5 Commands

Example:

[0] A:\ # getslots

1	MTRAS96-T1A	2
2	MT5634HD8	8
3	MT5634HD8	8
4	MT5634HD8	8

getsubnet

Parameter: None

Description: Displays the subnet mask for the MR9600.

Security: Guest

Example:

[0]A:\MMM # getsubnet Subnet mask = 255.255.255.0

[1]A:\MMM #

gett1

Parameter: Device

Description: Displays the current status of each t1 device

Security: Operator

Example:

[0]A:\MMM # gett1

5B T1 Online

13B T1 Online

gettemp

Parameter: None

Description: Displays the internal ambient temperature of the rack in Fahrenheit and Celsius.

Security: Guest

Limitations: CC9600 Only

Example:

[03]A:\ # gettemp

76.4 degrees Fahrenheit

24.7 degrees Celsius

gettrap

Parameter: None

Description: Displays the default trap IP address for the MR9600, if one is set. This is the address to which MR9600-generated traps, such as fault and status traps, are sent.

Security: Guest

Example:

[0] A:\MMM # gettrap

Trap IP Address = 199.199.99.91 [1] A:\MMM #

CommPlete Communications Server

43

Image 51

Contents MR9600 Controller User Guide Page Page Page CommPlete Communications Server CommPlete Communications Server Table of Contents Solving Problems Introduction Card Status LEDs LED IndicatorsIntroduction Product DescriptionIntroduction Ethernet Status LEDsConcentrator LEDs ConnectorsSpecifications MR9600 User Guide Installation Installation Procedure Serial Cabling Ethernet CablingMR9600 User Guide Quick Start MR9600 Quick Start Turn off all power to the CommPlete chassisSelect option 3, Configuration of RASExpress Select Setup Snmp Mode SupervisorSupervisor Console Quick Start Operation Security File SystemEvent Files Snmp Interface Command Line InterfaceGetting Modem Information Telnet InterfaceWeb Browser Interface LoggingWeb Interface Limitations FTP InterfaceOperation Page Commands Parameter Types ExamplesExample Display Commands Listed by FunctionFile Modem Control System Guest Commands Listed by Security LevelOperator Supervisor Security Guest Example Command ReferenceModules Parameter NoneAbort Security Guest Parameter NoneSecurity Operator Example Security Supervisor Example BootBpstatus ByeChdir Cfg, configureCat, type Cd, chdirDate ConfigureCl, clock Copy, cpDir, ls DownloadSecurity Supervisor E1setup E1cfgE1channelstatus, e1chstatus E1status ExitFormat Getcalls GetdevicesGete1 Getip GetfaultsGetfkey1, getfkey2, getfkey3, getfkey4 Getgateway Getmodems Getpowerstatus, getpsGetpri GetprichannelsGetrack Getslots GetrasGetreadcommunity GetsendtrapGettrap GetsubnetGett1 GettempListmod GetwritecommunityHaltsys HistoryMore Lo, logoutLoadmod Md, mkdirMount Oc, oosclear, oosclrOnline Passwd, password Oosset, osPing Poweroff PoweronPriocbchannels Priosbchannels PrisetupRassetup PristatusQuit Rd, remdir RasstatusRendir Reset, rsReadme Ren, renameSecurity Se, setenvironSetip SetconfigSetfkey1, setfkey2, setfkey3, setfkey4 SetgatewaySetpollingon SetpollingoffParameter On, off SetreadcommunitySetsendtrap SetsubnetTime SettrapSetwritecommunity SyncSecurity Supervisor Limitation CC9600 only Example T1cfgT1channelstatus, t1chstatus T1debugT1status T1setupUnmount UpdateType UnloadmodUptime UploadUsage UseridVer, version Whoami Error Messages Error Bad or missing configuration file Error No history is being maintainedError Password not changed Error Unknown errorMR9600 User Guide Solving Problems Introduction MR9600 Diagnostic Tests Solving Problems MR9600 User Guide Appendix Appendix a Updating the MR9600 Controller Firmware Index MR9600 User Guide Index IP address mask parameter IP address parameter