Multi-Tech Systems MR9600 manual Error No history is being maintained, Error Password not changed

Page 73

5 Commands

ERROR: No history is being maintained

The command history buffer is empty or not being maintained by the command line interface.

ERROR: Password not changed

The old password does not match the stored password; the new password is invalid; or the new password and the repeated new password do not match.

ERROR: Unknown error

An error of unknown origin occurred while the MR9600 was attempting to parse a command line.

ERROR: Bad or missing configuration file

The specified configuration file is not present on the system. It is possible that the file name is incorrectly spelled.

ERROR: Invalid number

The specified number is not a valid hex number starting with $ or a valid decimal number starting with a digit.

ERROR: Invalid device specifier

The device specifier is invalid since it is not of the format 1a, where 1 represents the slot number for the device and a represents the device number. See “Parameter Types” on page 22.

ERROR: Invalid drive specifier

The specified drive letter does not belong to a drive that is available to the system.

ERROR: Security information not changed

The new user ID is invalid. The new password is invalid; or the new password and the repeated new password do not match.

ERROR: Unable to update security information

The CMOS write error failed when updating the security information.

CommPlete Communications Server

65

Image 73

Contents MR9600 Controller User Guide Page Page Page CommPlete Communications Server CommPlete Communications Server Table of Contents Solving Problems Introduction Introduction LED IndicatorsProduct Description Card Status LEDsIntroduction Ethernet Status LEDsConcentrator LEDs ConnectorsSpecifications MR9600 User Guide Installation Installation Procedure Serial Cabling Ethernet CablingMR9600 User Guide Quick Start MR9600 Quick Start Turn off all power to the CommPlete chassisSelect Setup Snmp Mode Supervisor Select option 3, Configuration of RASExpressSupervisor Console Quick Start Operation File System SecurityEvent Files Snmp Interface Command Line InterfaceWeb Browser Interface Telnet InterfaceLogging Getting Modem InformationWeb Interface Limitations FTP InterfaceOperation Page Commands Examples Parameter TypesExample Display Commands Listed by FunctionFile Modem Control System Guest Commands Listed by Security LevelOperator Supervisor Modules Command ReferenceParameter None Security Guest ExampleSecurity Guest Parameter None AbortSecurity Operator Example Bpstatus BootBye Security Supervisor ExampleCat, type Cfg, configureCd, chdir ChdirCl, clock ConfigureCopy, cp DateDownload Dir, lsSecurity Supervisor E1cfg E1setupE1channelstatus, e1chstatus Exit E1statusFormat Getdevices GetcallsGete1 Getfkey1, getfkey2, getfkey3, getfkey4 GetfaultsGetgateway GetipGetmodems Getpowerstatus, getpsGetprichannels GetpriGetrack Getreadcommunity GetrasGetsendtrap GetslotsGett1 GetsubnetGettemp GettrapHaltsys GetwritecommunityHistory ListmodLoadmod Lo, logoutMd, mkdir MoreOc, oosclear, oosclr MountOnline Oosset, os Passwd, passwordPing Poweron PoweroffPriocbchannels Priosbchannels PrisetupPristatus RassetupQuit Rd, remdir RasstatusReadme Reset, rsRen, rename RendirSecurity Se, setenvironSetfkey1, setfkey2, setfkey3, setfkey4 SetconfigSetgateway SetipSetpollingon SetpollingoffSetsendtrap SetreadcommunitySetsubnet Parameter On, offSetwritecommunity SettrapSync TimeT1channelstatus, t1chstatus T1cfgT1debug Security Supervisor Limitation CC9600 only ExampleT1status T1setupType UpdateUnloadmod UnmountUptime Upload Userid Usage Ver, version Whoami Error Messages Error Password not changed Error No history is being maintainedError Unknown error Error Bad or missing configuration fileMR9600 User Guide Solving Problems Introduction MR9600 Diagnostic Tests Solving Problems MR9600 User Guide Appendix Appendix a Updating the MR9600 Controller Firmware Index MR9600 User Guide Index IP address mask parameter IP address parameter