Multi-Tech Systems MTCBA-C-EN-NX, MTCBA-E-EN, MTCBA-G-EN-FX manual

Page 19

Chapter 2 – Getting Started

11.From the workstation, open the command window by clicking the Start button and selecting Run.

12.Type CMD to open the command window. Click OK.

13.When the command window opens, type IPCONFIG /RELEASE to release your current IP received from the router.

14.Then type IPCONFIG /RENEW to renew your IP address from the router. You should also receive a DNS addresses from the router.

15.Close the command window.

16.Open a Web browser. You are now connected to the Internet.

Multi-Tech Systems, Inc. MultiModem Wireless Modem with Ethernet Interface (S000375F)

19

Image 19

Contents MultiModem Trademarks User GuideCopyright Record of Revisions Revision Date DescriptionTable of Contents Tools Packet FiltersGRE Tunnels Dhcp ServerProduct and Interface Descriptions Introduction Product DescriptionApplication Example Ship Kit Contents Ethernet Ports Caution Safety WarningsHandling Precautions Vehicle SafetyAT Command Information SpecificationsFeatures Edge Modems Gprs Modems Cdma Modems Getting Started Setup a Wireless AccountConnect Antenna, Ethernet, & Power Phone Numbers for the Wireless ModemOptional Attach the Modem to a Flat Surface Optional Fused DC Power ConnectionEthernet LEDs Front Panel LEDsModem LEDs Set Your PC’s TCP/IP Address for Ethernet Functionality Prerequisite Steps Using AT CommandsNetwork Registration Verification AT Command for Verifying Signal StrengthExiting Modem Mode Signal Strength RssiBenefits of Using the Wizard Setup Use the Wizard Setup for Quick ConfigurationOpen a Web browser Password PPP ConfigurationPPP Authentication AuthenticationShutdown Caution Set Time and DateConnecting to the Internet Steps Connecting to the InternetImportant Note About Provider Fees Page Navigating the Web Management Software Using the Web Management SoftwareServices Tunnels Logs IP SetupNetworks Web Management Software Screens IP SetupSyslog Configuration General ConfigurationIP Configuration Auto Dialout ConfigurationSubmit GeneralDaylight Configuration Time Zone ConfigurationImportant Note Daylight Saving Start TimeDaylight Saving End Time Add Static RoutesRemote Configuration IP Setup Remote ConfigurationIf NAT is disabled PPP PPP ConfigurationNAT Configuration If NAT is enabledIcmp Keep Alive Check PPP GeneralPPP Wakeup-on-Call Wakeup-on-Call ConfigurationCaller ID Configuration Caller Acknowledgement ConfigurationPPP Wakeup-On-Call Examples For Gprs and EDGE, it is *99***1# Set the Time Delay. Use can use the 10 second default Example of Useful Gprs AT Commands PPP Power-On ConfigurationPPP Modem Commands Power-On Init String ConfigurationNetworks & Services Network Configuration Networks & ServicesNetwork Configuration Service Configuration Networks & Services Service ConfigurationPacket Filters Packet Filters Packet FiltersPacket Filter Dnat Configuration Packet Filters Dnat ConfigurationPacket Filters Dnat Example Example MeterIP Example AnyExample Nochange Packet Filters Advanced Icmp ConfigurationConnection Tracking GRE Tunnels GRE Tunnel ConfigurationGRE Tunnels GRE Tunnels GRE Routes Configuration GRE Tunnels GRE Routes ConfigurationSubnet Settings Dhcp Server Subnet SettingsDhcp Server Tools Tools Dhcp Fixed ConfigurationTools Dhcp Server Fixed AddressesImportant Notes Tools Service StatusTools Firmware Upgrade Firmware UpgradeTools Save Configuration Tools Load ConfigurationLoad Configuration Statistics & Logs Ethernet Statistics & LogsStatistics & Logs Serial Statistics & Logs PPP Statistics & Logs SysInfo Statistics & Logs PPP TraceStatistics & Logs GRE Statistics Statistics & Logs Dhcp StatStatistics & Logs Modem Information Appendix a a Reference Table of Commonly Supported Subnets Appendix a Reference Table of Commonly Supported Subnets Antenna Appendix B Wireless AntennaGSM and E-GSM Radio Characteristics Cdma Radio CharacteristicsHow to Change the Fuse Fused DC Power Cable DimensionsObtaining the Latest Firmware Version Appendix C Firmware Upgrade Using External Tftp ClientMulti-Tech Warranty Statement Multi-Tech Warranty StatementRepair Procedures for International Distributors Replacement PartsWaste Electrical and Electronic Equipment Weee Appendix E Waste Electrical Electronic EquipmentIndex General Configuration IP Setup31, 32