Milan Technology MIL-S3580 manual Pre-Installation Requirements, Mounting the Switch

Page 11

3. Connecting to the Network

This section provides the installation procedure and instructions for assigning an IP address.

Pre-Installation Requirements

Before you start hardware installation, make sure you have the items listed below.

zPCs with 10/100Mbps Ethernet NICs or 100Mbps Fiber NICs: Your PC must have a standard Ethernet interface to connect to the switch.

zUTP cable with RJ-45 connectors or Fiber cable connectors: Check if the cable and connectors work properly.

zA power outlet with range 100 to 240VAC at 50 to 60 Hz: Make sure that the power switch is accessible and cables can be connected easily.

zDedicated power supply: Use dedicated power circuits or power conditioners to supply reliable electrical power to the network devices.

zA dry cool place: Keep the switch away from moisture. Avoid direct sunlight, heat source, and high amount of electromagnetic interference around.

zMounting tools: If you intend to mount the switch on a rack, make sure you have all the tools, mounting brackets, screws etc.

CAUTIION::

cCabling must be away from sources of electrical noise such as radio, computers, transmitters, broadband amplifiers, power lines and keep away from TVs, hair dryers, and microwave.

cAirflow around the switch and through its vents on the rear cannot be restricted.

Mounting the Switch

The MIL-S3580 is suitable for use in an office environment where it can be rack-mounted in standard EIA 19-inch racks or as a standalone device.

11

Image 11
Contents MIL-S3580 Page 90000397A Introduction FeaturesManagement Features Management Methods Package ContentsSnmp Network Management Console and Telnet ManagementFront Panel Hardware DescriptionLED Rear Panel Power OnDiagnostic Test Mounting the Switch Pre-Installation RequirementsDesktop Mounting Rack-mounted InstallationMount the MIL-S3580 in an EIA Standard 19-inch Rack Connecting to the SwitchConnecting the MIL-S3580 to a Terminal via RS-232 Cable Login in the Console InterfaceUser Interface TelnetMain Menu First ScreenSystem Information Management SetupSerial Port Configuration Network Configuration11. Snmp Community Menu Snmp Community SetupTrap Receiver Management Capability SetupDevice Control Menu Trap Filter Setup16. Switch Device Configuration Menu Switch Device ConfigurationPage 17. Switch Port Configuration Menu Switch Port Configuration18. Switch Port Configuration Menu Individual Port Configuration19. Permanent Address Configuration menu Permanent/Static Address Configuration20. Static Unicast Address Configuration Menu Static Unicast Address Configuration21. Static Multicast Address Configuration Menu Static Multicast Address ConfigurationPort Statistics Spanning Tree Protocol ConfigurationPage Port-Based Vlan Configuration Spanning Tree Protocol Port Configuration25. Port Based Vlan Configuration Menu 1Q Vlan Configuration Console configuration Web configuration 27. Static Vlan Port Configuration Menu Dynamic Vlan Table Vlan Tagged Configuration30. MTU/MDU Per-Port Vlan Table MTU/MDU Per-Port Vlan Table31. Garp Configuration Menu Garp ConfigurationIgmp Snooping Table Trunk Group Configuration34. Port Mirroring Configuration Menu Port Mirroring Configuration35. User Authentication Menu User AuthenticationSystem Utility System Restart 36. User Authentication Detailed Menu38. Factory Reset Menu Factory ResetSystem Download Login Timeout IntervalQuick Start Configuration Update SettingAbout Web-based Management System LoginSystem Information Management Setup Snmp Community Setup Menu Trap Receiver Menu Trap Filter Setup Menu Device Control Switch ConfigurationPage VLANs are assigned 12. Switch Port Configuration Menu 13. Trunk Group in Switch Port Configuration Menu 14. Port Mirror in Switch Port Configuration Menu Port Mirror ConfigurationPermanent Address Configuration Spanning Tree Protocol Configuration 17. Spanning Tree Protocol Configuration Menu 19. Port Statistics Menu Static Vlan Configuration Vlan ConfigurationConsole configuration Web configuration Dynamic Vlan Table Menu 21. Static Vlan Configuration Menu23. Untagged Configuration Menu 26. Garp Configuration Menu 27. Igmp Configuration Menu Igmp Configuration28. User Authentication Menu User Authentication29. System Restart Menu 31. Login Timeout Interval Menu 31. System Download Menu Update SettingCollapsed Backbone Application Network ConfigurationCollapsed Backbone Application Departmental BridgeDepartmental Bridge Application High Performance Switched WorkgroupPort-based Vlan Workgroup12s Ieee 802.1Q Vlan ApplicationShared Server Page Product Specifications Page 90000397A