LSI SAS2 manual 112, Initiator ID, Drive Type, Enclosure information Enclosure# Logical ID

Page 36

Appendix A: Commands

SAS2 Integrated RAID Solution User Guide

Sample Output Following is a sample of the information that the DISPLAY command returns.

Read configuration has been initiated for controller 0

------------------------------------------------------------

Controller information

------------------------------------------------------------

Controller type

: SAS2008

BIOS version

: 7.00.02.00

Firmware version

: 00.250.19.0

Channel description

: 1 Serial Attached

SCSI

: 112

Initiator ID

Maximum physical devices

: 62

Concurrent commands supported

: 266

Slot

: 3

Segment

: 0

Bus

: 64

Device

: 1

Function

: 0

RAID Support

: Yes

------------------------------------------------------------

IR Volume information

------------------------------------------------------------

------------------------------------------------------------

Physical device information

------------------------------------------------------------

Initiator at ID #112

 

Device at ID #335524

 

Device is a Hard disk

: 2

Enclosure #

Slot #

: 2

Connector ID

: 4

State

: Ready (RDY)

Size (in MB)/(in sectors)

: 70007/143374738

Manufacturer

: HP

Model Number

: DG072A9BB7

Firmware Revision

: HPD0

Serial No

: B365P720H7330709

Protocol

: SAS

Drive Type

: SAS

------------------------------------------------------------

Enclosure information

------------------------------------------------------------

Enclosure#

: 1

Logical ID

: 51234567:89012345

Numslots

:

8

StartSlot

:

0

Page 36

LSI Corporation Confidential August 2010

Image 36
Contents SAS2 Integrated RAID Solution Revision History Table of Contents Table of Contents Introduction to the Integrated RAID Solution FeaturesOverview Enhanced RAID 1EBenefits and Features Overview of Integrated RAID Mirrored Volumes IntroductionTypes of mirrored arrays Operation of Mirrored Volumes Typical Integrated Mirroring Implementation Integrated Mirroring Enhanced with Three Disks Mirrored Volume Features SAS2 Integrated RAID Solution User Guide Creating Mirrored Volumes Mirrored VolumeConfiguration Overview Please wait, invoking SAS Configuration UtilitySelect Create RAID 1 Volume Create New Array window appearsSelect Create RAID 1E Volume Expanding an Integrated Mirroring Volume with OCE Manage Array window appears Select New Array Type window appearsArray on this adapter Following figureManage Hot Spares window appears Smart supportHot Spare status changes to Yes Press C to create the hot spare diskOther Configuration Tasks Follow these steps to activate a selected volume Currently inactivePress Enter Select RAID Properties, and then press EnterFollow these steps to select a boot disk SAS2 Bios CU, select an adapter from the Adapter ListHighlight SAS Topology, and press Enter SAS Topology window appearsBoot Device on SAS Topology Window Boot disk or as a data disk Volumes can consist of two-to-ten disksOverview of Integrated Striping Integrated Striping Description Integrated Striping ExampleCreating Integrated Striping Volumes Creating Integrated Striping VolumesSelect Create RAID 0 Volume Viewing Volume Properties Activating an Array Select Delete Array Alternate device Following figure showsSAS2 Integrated RAID Solution User Guide Using the SAS2 Integrated RAID Configuration Utility Hardware and SoftwareRequirements Interface Description Commands EFICommand to get the enclosure and slot numbers of a drive GB of capacity on the disk driveFollowing fields of IOC Page 6 specify the configuration MPI2 specification and is specific for SSD drives only VolumeName a user-specified string to identify the volume Appearing while the command is runningSas2ircu controller# delete noprompt Sas2ircu controller# display filename112 Initiator IDDrive Type Enclosure information Enclosure# Logical IDConfiguration has changed or a drive has failed Failed FLD The volume has failedMissing MIS The volume is missing Initializing Init The volume is initializingSas2ircu controller# hotspare delete EnclosureBay Sas2ircu controller# status Volume status Enabled or Disabled  Physical disk I/Os Quiesced or Not quiescedSas2ircu list NoneSas2ircu controller# constchk volumeId noprompt Sas2ircu controller# activate volumeIdSas2ircu controller# logir action filename noprompt