McDATA 8832 warranty Remote Control Window

Page 11

IBM BladeCenter Deployment Guide

4.The Remote Control window is a pop up window. If you have a popup blocker installed, Remote Control will be blocked, so make sure popups are allowed for the management module IP. Note: Remote Control does work with Firefox, so if you are having trouble with the popup blocker in Windows XP SP2, Firefox may be a viable alternative.

5.The Remote Control window includes a tool bar (Figure 6) with “sticky keys” for passing “ctrl”, “alt”, and others keystrokes to the target system. This is particularly important when trying to enter setup screens, such as the QLogic setup which is accessed by hitting ctrl-Q”. Click on the sticky “ctrl” then hit Q when you see the message during POST.

6.If there is no keyboard response in Remote Control, confirm that the Remote Control window has focus. Click on the keyboard widget in the toolbar. There is also a known issue, fixed in the 73G release of the Management Module firmware, where the “ctrl” or the “alt” keys become stuck on. Clicking the icons on the toolbar twice should clear this state and may restore keyboard response.

Figure 6 Remote Control Window

7.If, during a Linux installation, you see the message “No Video Available” (shown in Figure 6) then most likely “nofb” was not specifying as a boot option. See Section 4.3 for more information.

8.When switching from managing one chassis to another, it is recommended that you close your browser after logging off from the first chassis, especially if you were using Remote Control in the first session. Otherwise, you may encounter errors with the Remote Disk applet (middle frame, Figure 5) in the second session such as “remotedrive.dll is not accessible” “exception: java.lang.NullPointerException.” “Initialization error. Library not installed” “Unsatisfied Link Error – Applet com.ibm.asm.remotedisk.RemoteDisk not inited.”

Version 3.0, 3/10/2006

http://w3-03.ibm.com/support/techdocs/atsmastr.nsf/WebIndex/WP100564

11

The BladeCenter Deployment Guide is intended as a personal productivity tool. It is not intended to be comprehensive and is provided for

guidance only, on an 'as is basis' without warranty of any kind. Please be aware that its contents have not been certified by IBM.

Image 11
Contents IBM BladeCenter Deployment Guide Part 3 Blades IBM Version 3.0, 3/10/2006 Table of Contents Table of Figures Table of TablesLinux nofb BladeCenter Subsystems Introduction OverviewBladeCenter Chassis Rear View ContributorsPreparatory Steps Network ConfigurationBladeCenter Management Module Remote Control Hints and TipsDisable key repeats Remote Control Window SAN Configuration Embedded Fibre Channel SwitchesStorage Connection Diagram Disabling ports on the QLogic switchUsing SANSurfer GUI Port Properties Device Startup Order Configuring the Blades for Remote BootCheck the Boot Order Disabling IDE devicesHS20 Boot Sequence Acquiring HBA WWPNs World Wide Port Names Configuring the Qlogic HBAConfiguring the QLogic HBA Configuring the path to the boot LUNEnable Selectable Boot Illustration Save your changes Testing the path to the boot LUNVerify Disk Media Ethernet Port NumberingMAC Address Port Browse MAC Address Table Top SwitchBrowse MAC Address Table Bottom Switch Learned MAC Address Port LearnedChange Media Tray Owner Loading the Remote Diskette Linux nofb Kickstart Information Multipath Red Hat InstallationBoot Failure for RH Fdisk Output Red Hat Linux AS Broadcom driver installationRPM Install of Broadcom Device Drivers Issues related to Red Hat AS 2.1/3.0 and bladesRev IBM Version 3.0, 3/10/2006 IBM BladeCenter Deployment Guide Other Linux Distributions and Blades Changing the Boot Loader ConfigurationOverview Rdac Installation and ConfigurationSerial Over LAN SOL for Blades 72345respawn/sbin/agetty -h ttyS1 19200 vt102 Summary of Linux changes for SOLAlt-sysrq from Linux client Alt-sysrqAlt-sysrq from PuTTY NetdumpIBM BladeCenter Deployment Guide IBM Version 3.0, 3/10/2006 List of limitations Broadcom Advanced Control Suite installationBMC Update for the HS20 8843 and LS20 Remote Update of the Firmware on an HS20 or HS40Bios and Ismp IBM BladeCenter Deployment Guide QLogic HBA Flash Flash the QLogic HBA Bios# mount -o loop drvnet.img mnt/drv Red Hat Boot Diskette Modification ProcessIBM Version 3.0, 3/10/2006 # cd # umount mnt/initrd Driverdisk --source=nfshost/path/to/26k4970.img Modify or Create the Post-install Driver Diskette ImageIBM BladeCenter Deployment Guide HS20 Model 8832 Firmware Information Management Module Bios InformationAppendix A. Firmware Versions HS40 Bios and Ismp Information HS40 BiosQLogic Firmware Information LS20 Bios and BMC InformationBladeCenter Components BladeCenter InformationIndex