Lucent Technologies USS-720 Getting Started Instructions, OSR2.1 Cable Installation Instructions

Page 8

Evaluation Kit for USS-720 Instant USB

Information Manual, Rev. 1

USB-to-IEEE1284 Bridge

September 1999

 

 

Getting Started Instructions

An initial evaluation of the USS-720 device can be performed using the In-System Design USB Smart Cable (i.e., the Lucent USS-720-based USB printer cable), the above-mentioned required hardware, and software supplied on the 3 1/2 in. diskette included in this kit. The basic evaluation procedure consists of the following steps outlined below for OSR2.1 and Windows 98:

OSR2.1 Cable Installation Instructions:

1.Connect the USB printer cable to a printer that is turned on and follow the instructions listed below. (Note that although it is not necessary to plug the USB printer cable into a printer to perform the following steps, the use of the printer provides a better demonstration of the USS-720 device's functionality.)

2.With the PC running OSR2.1/QFE 1214, plug the USB end of the USB printer cable into the PC's USB port.

A New Hardware Found box will appear stating that an Unknown Device has been found. Then, the Building Driver Information Database box will appear as the database is being built. At the end of this process, the Update Device Driver Wizard box will appear on the screen.

3.Follow the prompts to complete the installation of the Unknown Device, i.e., the USB printer cable:

a.Insert the diskette into the floppy disk drive.

b.Click on the Next button in the Update Device Driver Wizard box. Using the “Browse” button, direct the sys- tem to the Win95_OSR21 folder on the diskette to find the driver for the “Lucent USS720-based USB Cable.”

c.Click on the Finish button.

4.At this point, the files should automatically be copied from the diskette. The installation process is now com- plete.

Note: If a Plug and Play printer is being used, then a Plug and Play prompt may appear at this point to install the printer drivers.

5.To verify that the Lucent USS-720-based USB cable has been correctly installed, right click on My Computer, and then left click on Properties to access the System Properties box.

6.Choose the Device Manager tab in this box. The “Lucent USS720-based USB Cables” device type should appear in the list under “Computer”.

7.Double click on “Lucent USS720-based USB Cables”. Another entry, “Lucent USS720-based USB Cable” device will appear underneath.

8.Now double click on “Lucent USS720-based USB Smart Cable”. A “Lucent USS720-based USB Cable Proper- ties” box will appear. If the installation was successful, the device status will state that the device is working properly. If the installation was not successful, use the Cleanup.exe file on the diskette to first uninstall the soft- ware, then return to step 2 above.

Note: Cleanup.exe is a utility provided as a convenience to developers using the evaluation kit. It removes the driver files from the system. Cleanup.exe only works with the driver files provided with the evaluation kit and is not suitable, nor licensed, for distribution to end-users.

If the installation was successful and a printer was attached to the USB printer Cable in step 1, a test page can now be printed:

■Click on Start/Settings/Printers.

■Right click on the icon for the printer connected to the USB printer cable, then left click on Properties.

■Choose the Details tab. Select the correct USBLPT port [e.g., USBLPT1 (USB Port)] under “Print to the following port:”. Under “Print using the following driver:”, select the driver that corresponds to the correct printer. Click on the Apply button and then select the “General” tab.

■To begin the printing process, click on the Print Test Page button.

1-8

Lucent Technologies Inc.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Introduction Information Manual, Rev SeptemberTable of Contents Information Manual, Rev Evaluation Kit for USS-720 September USB-to-IEEE BridgeIOCTLSET1284REGISTER USS-720 USB Device Driver Preliminary User GuideIOCTL1284 Terminate USS-720 USB Port Monitor Application Note Evaluation Kit Contents Hardware Requirements \SAMPLESOSR2.1 Cable Installation Instructions Getting Started InstructionsSoftware Updates Windows 98 Cable Installation InstructionsPort Creation USB Driver and Port MonitorPlug and Play Eeprom Lucent Technologies Inc Lucent Technologies Microelectronics Group In-System Design, IncUSB Applications Support September Evaluation Kit Software USS-720 Driver Software Object Code License AgreementFebruary IntroductionUSS-720 Software Use Agreement February Licensed SoftwareFurnishing of Licensed Software OwnershipUSS-720 February Software Use AgreementWarranty and Indemnity Agreement PrevailsNothing Construed 04 ConfidentialityPublicity NonassignabilityAddresses IntegrationApplicable Law DisputesDocumentation USS720.SYSUSS720.INF USS-720 Software Use Agreement February Software Components Application Note, Rev FebruaryPrinter Enumeration Customer-Defined DataPlug and Play Operation PnP Power Management Installation ProcessOperating Systems Supported USB Hardware Types SupportedPrinter Types Supported Print Types SupportedDescription FeaturesPreliminary Data Sheet, Rev September Table of Contents USB-to-IEEE Preliminary Data Sheet, Rev USS-720Pin Information Parallel Port nAutoFd Signal Active-Low Parallel Port nSelectIn Signal Active-LowParallel Port nInit Signal Active-Low Parallel Port nAck Signal Active-LowOverview USB PortDevice Descriptor, Configurations, and Inter- faces Descriptor LocationsDevice Descriptor Offset Field Size Value Description USB-to- Ieee 1284 Bridge SeptemberOnboard Device Descriptor USB-to- Ieee Configuration DescriptorInterface Descriptors Bulk Out Endpoint Descriptor, I0A0E1Bulk In Endpoint Descriptor, I0A1E2 September USB-to-IEEE1284 BridgeBulk Out Endpoint Descriptor, I0A1E1 Interrupt Endpoint Descriptor, I0A2E3 Bulk Out Endpoint Descriptor, I0A2E1Bulk In Endpoint Descriptor, I0A2E2 Standard Requests PipesRequests Printer Class-Specific Requests Get Port Status Data Bit DescriptionSET1284REGISTER Vendor-Specific RequestsGET1284REGISTER Ieee 1284 Port Register-Based OperationRegisters GET1284REGISTER Data Byte Register DataInterrupt Pipe Read Data Byte Register DataParallel Port nFault Signal Reserved Status Register Address Bit SymbolDefault Bit Symbol Bit Description Control Register Address Bit Symbol Access Default Bit Symbol Bit DescriptionParallel Port nInit Signal USB-to-IEEE1284 BridgeUSS-720Instant USB ECP Command Register Address Bit Symbol Access Extended Control Register Address Bit Symbol Mode20 DescriptionUSS-720 Control Register Address Bit Symbol USS-720 Setup Register Address Bit Symbol Interrupts External Circuitry Requirements External Crystal ConnectionFilter Bypass Mode High Drive ModeSelf-Powered Mode Absolute Maximum Ratings Parameter Symbol Min UnitElectrical Characteristics Parameter Symbol Test Conditions Min Typ Max UnitCapacitance Values Parameter Unit Clklo ClkhiOutput Delay Timing Parameter Min Max Unit Timing CharacteristicsSetup and Hold Input Timing Parameter Outline Diagram Ordering InformationPin Mqfp Device Code Package ComcodeApplication Note February Description Parallel PortBridging USB to Typical Circuit Showing USSLucent Technologies Inc Signal Directions Preliminary User Guide, Rev FebruaryIOCTL1284 Setmode Initialization O File FunctionsPreliminary User Guide, Rev USS-720 February USB Device DriverCreateFile Error Codes ReadFileWriteFile DeviceIoControl CloseHandle O Control Codes Control Code DescriptionIOCTL1284 Ecpfwdtorev ParametersIOCTL1284ECPREVTOFWD IOCTL1284 Ecpsetchannel Register Mode Description IOCTL1284 SetmodeIOCTL1284 Terminate Ioctlabortpipe Value DescriptionBulkoutpipe BulkinpipeIoctlcancelpiperequest IOCTLGET1284REGISTER Ioctlgetaltsetting ALTINTERFACE0ALTINTERFACE1 ALTINTERFACE2Ioctlgetcapabilities Ioctlgetconfigurationdescriptor Ioctlgetdevicedescriptor Ioctlgetdeviceinstances Ioctlgetinterface Ioctlgetportstatus Bit MeaningIOCTLISSUEUSS720COMMAND Command DescriptionIoctlreadinterruptpipe Byte DescriptionIoctlresetpipe IOCTLSET1284REGISTER Ioctlsetaltsetting Ioctlsoftreset O Control Data Structures DeviceinstanceheaderDeviceinstance Data StructureREGISTER1284 REGISTER1284, *PREGISTER1284ADVREGISTER1284 ADVREGISTER1284, *PADVREGISTER1284Lucent Technologies Inc USS-720 USB Port Monitor USS-720 Application Note USB Port Monitor February Printer Cable with Instant USBSoftware Installation Instructions W98USS720EvalKit2402.zip to download the installation filesApplication Note June Click on Enter LibrarySeptember MN99-052CMPR-1 Replaces MN97-061CMPR-04
Top Page Image Contents