Korg KTV1 Creating a clip -Sampling and Quick Editing, Sampling video, Time-lapse sampling

Page 23

Creating a clip —Sampling and Quick Editing

1. Sampling

Sampling video

Sampling a video input source

1Press the SAMPLE key; it will blink, and you will be in Sampling mode. You can press the SAMPLE key once again to exit Sampling mode.

2Use the VALUE knob to specify the sampling time. Samples are created and stored using memory units that are 8 seconds long. You can specify a time length from eight seconds through 600 seconds (ten minutes) in eight-second steps. The default is eight seconds.

NOTE The sampled video is managed in units of data that are each eight seconds long. For example, if the image you want to sample is fourteen seconds long, it will require two of these eight second data units, and will actually occupy sixteen seconds of sampling time on the hard drive.

3Selecting an empty clip.

If you press the YES/WRITE key at this time, a vacant clip pad in the lowest-numbered available bank will be selected. You can also manually select any empty clip pad in any bank. If you select a clip pad that already has a clip assigned to it, the display will indicate “OCCP”. If there is not enough available storage space when you press the clip pad, the dis- play will indicate “FULL”.

The kaptivator will be in sampling-ready mode. (The clip pad and the REC key will blink.)

4Press the INPUT key to select the external video input signal that you want to sample. You can also apply an effect to the input video while sampling it. If you want to do this, press the STYLE key at this point, turn the value knob to select an effect, and press the YES/ WRITE key.

NOTE The effect selected in this case is only applied to the image being sampled.This will not change the effect setting of the style that was selected before you entered SAMPLE mode.

5Press the REC key to begin sampling. Press the STOP key to stop. Sampling will stop auto- matically when the specified sampling time has elapsed.

6If you want to continue sampling, press the YES/WRITE key to select the next empty clip, rotate the VALUE dial to set the sampling time, and repeat steps 4 and 5.

7If you are finished sampling press the SAMPLE key to exit Sampling mode. If the kaptivator is in sampling-ready mode (The clip pad and the REC key are blinking), press the NO/ESC key, and then press the blinking SAMPLE key to exit Sampling mode

NOTE The Clip Edit parameters allow to adjust the playback speed, start point, end point, playback method, etc.

Time-lapse sampling

Extremely slow movements such as drifting clouds or opening flower blossoms can be cap- tured using time-lapse video, and then played back to speed up the movement. Time-lapse video can also be used to make common things like cars and people play back at an artifi- cially fast speed.

1Press the SAMPLE key to enter Sampling mode.

2Hold down the EDIT key and press the SAMPLE key; the EDIT key and SAMPLE key will blink, and the display will indicate the time-lapse ratio.

NOTE You can turn the knob quickly to make larger changes in the numerical value.

Owner’s Manual

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Page Precautions About the video clip collection About your dataHandling of the internal hard disk Table of Contents Introduction Main featuresTop panel Controls and connectorsValue knob YES/WRITE key Front panel Video Input indicatorAudio Trig Input L/R jacks Rear panelBasic connections Connection diagramSelecting the DV connector input/output setting About video signal formatsStyles Basic concepts and operationConcepts Sampling videoTerms Monitors Turning the power on/offPower Basic operation PlaybackSelecting a style Selecting and playing videoPlaying a clip Selecting a bankTo select an external video source Working with external video sourcesViewing an external video source Mixing an external video source with a clipSynchronizing to music Setting the BPMSynchronized playback using the BPM setting Synchronizing the start of the clip to the audio trigger Synchronized playback using an audio triggerAdjusting the audio trigger level Using an external audio signal to control an effectRecording a motion sequence Using Motion SequencesPlaying a motion sequence Looping the playback of a motion sequenceErasing a motion sequence Style editing Customizing a Style -Style EditingEditing a style Choosing a styleChanging the wipe type Editing examplesChanging the operation of the ribbon controller Sampling a video input source Creating a clip -Sampling and Quick EditingSampling Sampling videoResampling to a clip Capturing video and using it as an input sourceMain Out Capture Editing a clip ClipsCopying a clip Erasing a clipTurning Protect On or Off Copying an entire bank of clips BanksCopying a bank Assigning a bank to a clip pad groupNavigating the Utility mode Utility modeOperations in Utility mode Entering Utility modeHDD free Utility menu items and proceduresMidi setting Setting the control change numberBacking up video data to an external device Power on setupBackup Restoring video data Restoring style or motion sequence data Preset InitializeBacking up style and motion sequence data Style Parameter List Parameter listGroup B Operation settings Controller Assignment list Start Variation listDual Routings Routing listSingle Routings Three-layer Routings Separate output Routings Main OUT Monitor OUT Parameter A2 A5 = 02 Wipe Transition listParameter A2 A5 = 00 Fade Parameter A2 A5 = 01 WipeEffect list Enabled 1 and EnabledPattern 1 Normal Loop Clip parameter listPlayback Type and Playback Pattern selection Type 1 Specified End PointPattern 5 Reverse Alternating Loop Type 2 Tempo and Beat Specified End PointPattern 3 One-Shot Pattern 4 Reverse Normal LoopPattern 4 Reverse Alternating Loop Type 3 Specified Loop Point and End PointPattern 1 Normal Pattern 3 Reverse Normal LoopType 4 Tempo and Beat Specified Loop Point and End Point Tips for working with the kaptivator Using BPM to control the video playback speedUsing the kaptivator with your computer AppendixSampling video from your computer into the kaptivator Managing data on the hard driveUsing Midi to work with clips Trobleshooting Specifications Preset Style listStyle Cheat PresetVideo Effect settings Controller will apply a video Style User KTV1 Midi Implementation Data Processload Completed CONT# Midi Implementation Chart Important Notice to Consumers
Top Page Image Contents