Lantronix 4092A IRIG-B manual Appendix a Specifications, Electrical Specifications

Page 29

Appendix A: Specifications

A.3 Electrical Specifications

Table 3 lists the electrical specifications for the 4092A.

Table 3: Electrical specifications

Item

Specification

 

 

 

 

Protection Class

Class I (Grounded Type)

 

 

 

 

Power Input Voltage

100–240 V ~ 50/60 Hz 0.5 A, power dissipation ~20 Watts

 

 

 

 

 

 

 

Note: Fluctuations not to exceed ± 10% of nominal supply voltage.

 

 

 

 

 

 

 

 

Power Inlet Type

IEC 60320 sheet C14

 

 

 

 

AC Power Supply Cord Set

18 AWG (0.75 mm2 minimum)

 

DC Power Supply

The external wiring to this connector must be at a minimum 1.5 mm² (14 AWG)

 

 

with a 15 A fuse or circuit breaker. A 20 A circuit breaker may be used if the

 

 

external wiring is jacketed 14 AWG, with maximum length of 20 feet. An

 

 

internal fuse mounted on the power supply carrier board is included to protect

 

 

this input but is not field replaceable. Mating connector for the DC power

 

 

supply is a AMP 1-350344-0 and 2 sockets are required, AMP 350388-1.

 

 

 

 

Power Supply Part Numbers

AC: TSC 4501A

 

 

DC: TSC 4502A

 

 

 

 

Power Mains Fuse

AC: (2) - 250V~1A time lag 5 x 20 mm. Initial shipments will have one fuse.

 

 

DC: No customer-serviceable fuses.

 

 

 

 

Unmodulated Signal Input

„ Frequency: 1–200 kHz

 

 

„ Lo-Z Impedance: 50 Ω ±5 Ω

 

 

„ Hi-Z Impedance: 600 Ω ±10 Ω

 

 

„ Input level: > 1.5 V peak to peak into 50 Ω

 

 

 

 

Modulated Signal Input

„ Code Format: IRIG-B

 

 

„ Frequency: 1 kHz (IRIG-B)

 

 

„ Lo-Z Impedance: 50 Ω ±5 Ω

 

 

„ Hi-Z Impedance: 600 Ω ±10 Ω

 

 

„ Input level: > 2.8 V peak to peak into 50 Ω

 

 

 

 

Connectors

„ Input: 2 BNC

 

 

„ Output: 8 BNC

 

 

„ LAN: RJ-45

 

 

 

 

Gain

0 dB

 

 

 

 

Isolation

> 70 dB

 

 

 

 

 

4092A Operations and Maintenance Manual

25

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Walnut Street Suite 1B Boulder, CO Phone 303 Revision Description Date Approved Contents Glossary Index Introduction SymbolsSymbol Definition Convention Definition About This ManualConventions 4092A Overview AC Power EthernetIntroduction Installing the 4092A Installing and Setting Up the 4092ASafety Information Assigning a Static IP Address To set up the 4092A4092A Operations and Maintenance Manual Selecting the Active Input Channel To assign the static IP address using TelnetTo select the active input channel from the front panel To select the active input channel remotelyCleaning Setting the 4092A to Autoswitch ModeTo set the 4092A to autoswitch mode from the front panel To set the 4092A to autoswitch mode remotelyInstalling and Setting Up the 4092A Checking Status and Alarms Accessing the SystemMonitoring the 4092A Checking System InformationDefines each status or alarm bit position Command sent 4092A response To check the software version Checking Model Number and Software VersionTo check the TSC model number Understanding Alarm Output Monitoring the 4092A Input LED status What it means What do to Troubleshooting the 4092ATroubleshooting Input Problems Troubleshooting Power Supply Problems Troubleshooting Output ProblemsPower LED status What it means What do to Input Select LED status What it means What do toTo change the jumper settings Configuring for Input Signal and ImpedanceConfiguring for Dual Power Supplies To change the jumper setting Replacing Power SuppliesTo replace a power supply Verifying Operational ProblemsReplacing Fuses To replace a fuseTroubleshooting the 4092A Warranty Information Warranty and Shipping InformationShipping Information Packing InstructionsWarranty and Shipping Information Specification Appendix a SpecificationsElectrical Specifications Temperature Relative Humidity Altitude Physical SpecificationsEnvironment Specifications Glossary Glossary Numerics IndexIndex

4092A IRIG-B specifications

The Lantronix 4092A IRIG-B is a high-performance time code generation and distribution module that plays a crucial role in various applications requiring precise time synchronization. This compact device is particularly beneficial in systems such as telecom infrastructure, military applications, satellite communications, and scientific research. Its core functionality revolves around generating and managing the IRIG-B time code, a standard used for accurately transmitting time information.

One of the primary features of the Lantronix 4092A is its versatility in time code generation. It supports both unidirectional and bidirectional protocols, allowing for seamless integration into existing systems. The module can generate multiple IRIG-B formats, ensuring compatibility with a wide range of time synchronization devices. This flexibility is a significant advantage, particularly in environments that utilize various time code standards.

The device employs advanced timekeeping technology that ensures high accuracy and stability. Equipped with a GPS input option, the 4092A can synchronize its time code with GPS signals, obtaining precise time data globally. This feature is essential for applications that demand synchronization across extensive networks and geographical locations.

In terms of connectivity, the Lantronix 4092A IRIG-B offers multiple options, including RS-232 and RS-485 interfaces. This variety enhances its compatibility with various systems and makes installation straightforward. Additionally, the module is designed for easy integration, enabling developers to embed it within existing hardware architectures without significant modifications.

The 4092A also boasts user-friendly configuration capabilities. Its setup can be managed through a serial interface, allowing users to define parameters and adjust settings with ease. This feature ensures that the device can be quickly tailored to meet the specific needs of the application, minimizing downtime during deployment.

In conclusion, the Lantronix 4092A IRIG-B is an essential module for any application that requires robust time synchronization. Its main features, including versatile time code generation, advanced timekeeping technology, multiple connectivity options, and user-friendly configuration, make it an outstanding choice for industries where precision timing is critical. With its reliability and adaptability, the 4092A is poised to meet the challenges of modern time-sensitive applications.
Top Page Image Contents